Bedienungsanleitung Cola JOHANNA SX (Seite 9 von 16) (Englisch)

669028

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Johanna

1.8 Ordering replacement parts

For the end-user:

Contact your service centre and/or dealer to order replacement parts

For the dealer:

To request any replacement parts contact the Cola s.r.l. service centre and/or send a fax clearly specifying the

following data:

- stove model;

- serial number;

- date of purchase;

- list of replacement parts;

- details of faults encountered.

- Operations on parts must be carried out by authorised and/or qualified personnel.

- Only use original Cola replacement parts.

1.9 Stove decommissioning

For disposal, the stove must be sealed inside strong packing; contact your local authority for information on how to

proceed in accordance with the current local regulations.

2 – TRANSPORT AND INSTALLATION

2.1 Packing, handling, shipment and transport

The stove can be lifted using a lift truck, inserting the forks (of suitable length) in the special spaces in the wooden

packing.

Make sure the equipment used for lifting and transport can take the weight of the stove, specified on the dataplate and

in this manual.

Avoid taking the load in areas where it could be a danger if dropped.

Set the stove down on the floor carefully without bumping, and position it in the required place; make sure the floor can

take the weight of the stove, otherwise consult a specialised technician.

2.2 Instructions for safe installation

Correct operation of a heating stove depends above all on its installation, which must be carried out by a competent

person, in compliance with the current safety regulations.

An incorrectly installed stove can be the cause of serious accidents (flue, insulation materials, etc., catching

fire).

The sides and back must be at least 20 cm from flammable materials. If the floor is made of flammable material (wood,

carpets, etc.) provide for a protection base in sheet metal (recommended min. thickness 2-3 mm).

2.3 Connection to the flue

The JOHANNA stove must be connected to the flue by means of the collar on the hotplate, using flue pipes that are

readily available on the market. Connection to the flue must be made using strong and stable pipes (recommended

min. thickness 1.5-2 mm). The flue pipe must possibly be straight, to avoid pressure losses, and towards the flue. The

ends of the flue pipe must be tight.

To ensure regular operation, the flue draught with stove operating must be between 10 and 14 Pa.

For optimum stove efficiency, a draught control or

damper must be fitted in the

flue pipe or chimney.

Every unit must eliminate the fumes through its own flue; never use the same flue for several units.

2.4 Room ventilation

The air necessary for combustion, i.e. up to 25 m³ every hour, must be ensured in rooms where stoves with natural flue

draught are installed. The air change must occur through several fixed openings to the outside, whose cross section

must comply with current local regulations. Such openings must be protected with grilles and must never be obstructed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cola JOHANNA SX Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info