Bedienungsanleitung Cola TERMO POWER 30S (Seite 57 von 175) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

669018

Zoom out

Zoom in

Vorherige Seite

1/175

Nächste Seite

T-POWER30_T-POWER 30S

When the water temperature has reached the set value,

as a condition also at the same time as that described in par.4.4.1,

the output is automatically brought to the min. value,

MODULATION status.

As for idro model stove, when the water temperature parameter

can’t be reached, the activation of led [ A ] starts.

4.4.3 Restart from STANDBY

After shutdown, the stove goes to cooling status, bringing the fume

extractor speed to the set value for brazier cleaning. Relighting

occurs as soon as the room temperature reach the SET value.

4.4.4 Cleaning the brazier

During normal operation in work mode, the 'BRAZIER CLEANING'

mode is activated at fixed intervals for a set duration.

4.4.5

Water heater with heat exchanger quickly

When hot water is required, the display shows the word SCAM HEALTH and LED lights shown from the tap. The

function, however, is only executed if the stove is lit, and has reached a sufficient temperature inside the camera.

In the remaining cases the service is not provided.

4.4.6 Water heater with storage tank

This type of installation requires the use of an external thermostat, which measures the temperature of the water of

the kettle. When the temperature drops below the set temperature of SET in the external thermostat activates the

function of health, the display shows the message of the stove and boiler HEALTH LED lights shown from the tap

until the request is satisfied.

If the stove is in the HOLD step REQUEST automatically turns on and you put in WORK. Once the temperature of

water in the camera work, you turn the water supply to the boiler.

SET When the temperature of the tank is met, the oven converts waste heat to the heating for about 2 minutes and

then, if there is another request, it waits or REQUEST MODULATION, according to the settings ( see prg. 4.6.5).

If the stove is in the OFF state, no lights and does not provide the service.

4.4.7 System with puffer / heat storage

This type of installation requires the use of an external thermostat, which measures the temperature of the puffer.

When the temperature is lowered below the temperature of SET set in the external thermostat, in the stove display

shows the message WATER PUFFER or BOILER WATER and light up the 2 LEDs respectively indicated by the tap

and from the radiator as it can meet the plant heating system.

If the stove is in the HOLD step REQUEST automatically turns on and goes into WORK and reached the working

temperature of the water in the camera, you turn the water supply to the puffer.

SET When the temperature of the puffer is satisfied, the stove is placed in a HOLD REQUEST (it is recommended to

set the function ON STAND-BY, see prg. 4.6.5).

If the stove is in the OFF state, no lights and does not provide the service.

Dialogue box

Clock

Room temperature

Water temperature

Dialogue

Clock

Set output

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cola TERMO POWER 30S Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info