521985
17
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
CSB200 Class B AIS
R2.0 33
TROUBLESHOOTING GUIDE
Problem Possible cause Solution
General
CSB200 is not
detected on proAIS
The AIS is not
connected to the
serial port selected
from the drop down
menu.
The AIS is not
powered.
The serial cable is
damaged or faulty.
Check the number of
the serial port the AIS is
connected to and retry.
Check that the power
supply is connected
and switched on.
Try an alternative serial
cable.
Static Data tab
No static data is
displayed
The unit has not yet
been configured
Follow instructions in
the Static data section
to configure the unit
The MMSI can not
be changed
The MMSI has
already been
programmed
The MMSI can only be
programmed once. If it
is incorrect please
contact your dealer.
The static data is
incorrect
Data was entered
incorrectly
Re-enter the static data
and save to the AIS.
The MMSI cannot be
updated.
GPS tab
No GPS position
information is
displayed
(or graph shows only
blue bars)
The unit has not
acquired GPS fix
Check the GPS
antenna connections
and power cycle the
AIS unit.
CSB200 Class B AIS
R2.0 34
Problem Possible cause Solution
The GPS antenna is
not correctly
connected
The GPS antenna
does not have a clear
view of the sky
GPS antenna is
unsuitable for use with
AIS
Check the GPS
antenna location and
make sure it's view of
the sky is not
obstructed
Check the AIS
installation manual
against the specification
of your GPS antenna
Diagnostics tab
Red cross against a
status item
Unit configuration or
antenna connections
See Diagnostics tab
section of this user
guide for advice on
each item
Active alarm shown:
Position sensor fault
OR
SOG data fault
OR
COG data fault
The unit has not
acquired GPS fix
Wait at least five
minutes for the unit to
acquire GPS position fix
Follow troubleshooting
guide for GPS tab
Active alarm shown:
VHF Antenna VSWR
fault
The VHF antenna is
not connected or is
not suitable for use
with the AIS
Check the VHF antenna
connections.
Check the AIS
installation manual
against the specification
of your VHF antenna
Active alarm shown:
12V Power supply
fault
The power supply to
the AIS is outside the
specified range.
Check the power supply
voltage to the AIS
against that specified in
the installation manual.
www.Busse-Yachtshop.de email: info@busse-yachtshop.de
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Comar CSB200 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info