Bedienungsanleitung CombiSteel 7227.0010 (Seite 12 von 88) (Deutsch, Englisch, Holländisch, Französisch)

778172

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

www.combisteel.com

Installation

Installations (refer to Page 4 for parts): Measure the

distance between stove top and the bottom of range

hood. A distance of 27” to 30” is recommended*.

*Due to different ceiling height configurations,

recommended height may not be applicable.

1. You have two ways (A or B) to mount this range hood:

A. Proceed if you would like to mount this range

hood without using the hood-mounting bracket.

1. Using references in Height & Clearance on Page 8 and Mea Measurements and Diagrams on

Page 17, center the hood beneath the cabinet and flush with the front of the cabinet.

2. Draw electrical wires through cabinet access opening and center the hood beneath the

cabinet.

3. From inside of the hood, place screws into the exact center of each knockout hole and secure

to cabinet bottom. Finish tightening all screws until secure. Be careful when using electrical

screwdriver, damage to the range hood may occur. Skip Part B below and proceed to Step 2.

CAUTION: Make certain the range hood is secure before releasing!

B. Proceed if you would like to mount this range hood using the provided hood-mounting bracket.

1. Using references in Height & Clearance on Page 8 and Measurements and Diagrams on

Page 17, mark the leveling point of the hood. Position two mounting screws on the wall, leaving

1/8” space away from the wall. Mounting the hood on wall studs or lumbers is highly

recommended.

2. Attach the hood-mounting bracket to the back of the hood with six screws as shown in

Figure 3.

3. Puncture the knockout wire access hole at the back of the hood and draw the electrical wires

through as shown in Figure 4.

4. Align hood-mounting bracket to the screws on the wall and hook hood into place as shown

in Figure 5. Tighten screws to secure hood to the wall.

CAUTION: Make certain the range hood is secure before releasing!

2. For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a more secure

installation, use as many mounting holes as needed to secure from the inside of hood.

3. Use 8” round steel pipe (follow building codes in your area) to connect the exhaust on the hood to the

ductwork above. Use silver tape or duct tape to make all joints secure and air tight. Refer to Figure 6.

SAFETY WARNING: Risk of electrical shock. this range hood must be properly grounded. Make sure this is done

by qualified electrician in accordance with all applicable national and local electrical codes. Before connecting

wires, switch power off at service panel and lock service panel to prevent power from being switched on

accidentally.

4. Connect the range hood to a designated standard outlet or cut off the plug and connect three wires (black,

white and green) to house wires and cap with wire connectors.

5. Store excess wires in the wiring box.

6. Drop oil tunnel into recess support near rear of hood. Refer to Figure 8.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

CombiSteel 7227.0010 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info