Bedienungsanleitung Concept2 Model C (Seite 19 von 38) (Englisch)

738048

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

  •Reorientorrelocatethereceivingantenna.

  •Increasetheseparationbetweentheequipmentandthereceiver.

  •Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.

  •Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

LEVEL III. extra functions (for advanced users)

All of the PM2 buttons except the ON/OFF button have extra functions which are activated when you press and

hold down the READY button.

These special functions include:

• Two Odometers: one is resettable (trip odometer) and one is not resettable

• Split Intervals: you can set the PM2 to measure splits at intervals which you set. Each split will be saved for

recall after you ﬁnish and can be displayed for 6 seconds while you row.

• Drag Factor: you can set the PM2 to display the drag factor which it calculates during the rundown of the

ﬂywheel.

• PM2 Display Test

BUTTON SEQUENCES & DESCRIPTIONS OF EXTRA FUNCTIONS:

RECALL

ON/OFF DISPLAY

SET DIGITS

REST

READY

TIME METERS

/500 m

WATT

CAL

� �

▲▲

▲

Hold

down

Custom Splits (distance)

to have splits displayed during

your workout. Repeating this

button sequence will turn off the

split display during your workout.

When the PM2 powers up, splits

are off by default.

Hold

down

Splits On/Off

to perform a self-test including all

segments test. Press ON/OFF to end

the test.

Hold

down

then

press

READY

DISPLAY

PM2

DISPLAY

TEST

to set a time interval for split

measurement. Use the SET DIGITS

buttons to set the split time. Then

press READY when done. Note:

your custom split interval will not

be retained through a power down.

Default value is 2 minutes.

Hold

down

Custom Splits (time)

SPLITS

READY TIME READY METERS

READY RECALL

then

press

then

press

then

press

to set a distance interval for split

measurement. Use the SET DIGITS

buttons to set the split distance. Then

press READY when done.

Note: your custom split interval will

not be retained through a power

down. Default value is 500 meters.

DRAG

FACTOR Hold

down

to have a drag factor displayed in the lower right display window.

Repeating this button sequence will turn off the drag factor

display. The drag factor is most helpful if you row on Concept2’s

in different locations and want to be sure the resistance setting

is the same. Check the drag factor on your “home” machine,

and then adjust the damper on the “away” machine until you

get the same drag factor. Typical range for drag factor on the

Indoor Rower is: 103 (damper setting 1)-223 (damper setting

10). When PM2 powers up or resets, the drag factor display

will be off by default.

Note: When a heart rate monitor is being worn, HR will override

the drag factor and will always be displayed.

READY REST

then

press

Hold

down

then

press

READY SET DIGITS

Not Resettable

to display cumulative distance

rowed. This odometer is not

resettable. Distance is in kilometers

and is only displayed when READY

and are being pressed.

Hold

down

READY SET DIGITS

Resettable

to display a resettable record of

distance rowed. At 99,999 it rolls over

to 00,000. Press RECALL to reset to

0. Press READY or ON/OFF to get

out of this function.

then

press

TWO ODOMETERS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Concept2 Model C Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info