Bedienungsanleitung Concept CA1010 (Seite 20 von 36) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch)

804453

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

CA1010

PRODUCT DESCRIPTION

1 Display

2 Air outlet cover

3 Appliance body

4 Lower grille

5 Filter

6 Appliance base

INSTALLING THE FILTER

• Turn the lter base counterclockwise (Fig. 1).

• Insert the lter.

• Insert the base back and turn it clockwise.

USE

TIMER: When the appliance is running, the operating time can be set using the “timer” button. Set the time to 1 hour, 2 hours, 3 hours, press again to turn o,

the corresponding indicator lights up after the selected time.

Fan speed: Press the fan speed button to change the speed (1-3).

RESET: The appliance is equipped with a lter replacement alert function. When the lter replacement indicator lights up, replace the lters. Then hold the

button for 3 seconds and the countdown will reset.

Ionization: Use the ionization on/o button to switch ionization on or o.

INSTALLATION INSTRUCTIONS

• In case of internal dust, such as pollen, the appliance should be placed on the ground. Since pollen, dust, etc. are usually held close to the oor, it is

recommended to place the purier on a at oor in the room.

• In order not to block the air inlet and outlet, place the appliance about 30 cm or more away from the left and right sides of the wall, furniture, curtains,

etc. For eective use of the appliance, please keep it at least 20 cm away from the wall behind it.

• Do not place any objects on the top of the appliance (this may cause the appliance to malfunction).

• Note: Do not place magnets or metal objects on the appliance.

• Do not block the air inlet and outlet, for example, do not place any objects on the air outlet. Or on the front side, on the air inlet.

MAINTENANCE

Disconnect the mains supply before cleaning and maintenance.

• Place the lter in a ventilated area so that harmful gases and bacteria on the lter surface can evaporate. Do not expose it to excessive sunlight.

• Do not wash the lter with water.

• Do not work with the lter removed (operation without the eect of removing dust may cause the appliance to malfunction).

• If the appliance is idle for a long time, unplug the power cord (it also consumes power in standby mode).

TROUBLESHOOTING

Common faults, error code description and troubleshooting method.

Problem Cause Remedy

It is not possible to turn on or press the

button, no response Is the power cord plugged in? Plug in the power cord.

The odour from the appliance outlet is

unpleasant Is the lter installed correctly? Follow the installation instructions and

precautions.

The purier runs for a long time, but the air

quality does not improve signicantly

The lter indicator is on: this means that the

lter replacement timer has reached the

set value.

After replacing the lter, press the button to restart

the lter.

Control panel

A Ionization on/o

B Light

C Fan speed

D Wi-Fi symbol

E On/o button

F Timer

G Filter restart

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Concept CA1010 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info