804417

Concept CP2000 Seite 30

30
Zoom out
Zoom in
Vorherige Seite
1/71
Nächste Seite
1. Connect the steam cleaner into the mains. Press the power on/
off button, the indicator will light blue.
2. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
3. Put your foot on the head and angle the body of the cleaner downwards
(6).
4. Press the trigger to release the vapour (7).
5. Move the cleaner slowly backwards and forwards paying particular
attention to frequently used areas.
CARPET CLEANING
NOTE: Always vacuum or sweep the floor prior to use the steam cleaner.
IMPORTANT: Do not use the cleaner without the Textile Pad attached to
the Head.
1. Attach the Carpet Glider to the Head (10).
2. Connect the steam cleaner into the mains. Press the power on/off
button, the indicator will light blue.
3. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
4. Put your foot on the head and angle the body of the cleaner downwards
(6).
5. Press the trigger to release the vapour (7).
6. Move the cleaner slowly backwards and forwards paying particular
attention to frequently used areas.
MANUAL CLEANER OPERATION
1. Press the Manual Cleaner Release Button and remove the steel tube
(11).
2. Remove the Head (12).
3. Press the Water Tank Release Button and remove the Water Tank (3).
NOTE:A tube feeding water from the water tank to the boiler is loaded with
a brass ball. This design is intentional and serves to increase the efficiency
of water use. It is normal for this ball to create a rattling sound inside the
Water Tank during operation.
4. Pull the Water Tank by the cap and open it (4).
5. Fill the tank with cold tap water. Secure the tank with the cap (4). Do
not add any chemicals, detergents or perfumes to the Water Tank.
NOTE: We recommend to use distilled or de-mineralized water in order to
reduce building up mineral deposits and prolonging the life of the appliance.
EN
57CP 2000
6. Put the Water Tank back on the main part of the cleaner and make sure
the Water Filter is installed.
7. Connect the steam cleaner into the mains. Press the power on/
off button, the indicator will light blue.
8. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
9. Press the trigger to release the vapour (on the manual cleaner)(13).
IMPORTANT: Always disconnect the cleaner from the mains prior to
removing the Head or handling the appliance. Always ensure the cleaner
has fully cooled down before removing the Head.
SOLUTION TANK USE
1. Rotate the Solution Tank cap counter-clockwise to open and fill the tank
with a solution fluid (8).
2. Put back the Solution Tank cap and screw it clockwise.
3. Press the foot pedal to the ON position to engage the Solution Tank.
Press the foot pedal to the OFF position to disengage.
IMPORTANT:To prevent solution from leaking ensure the foot
pedal is in the OFF position when the product is not in use.
Empty the solution tank
1. Connect the steam cleaner into the mains. Press the power on/off
button, the indicator will light blue.
2. Remove the Solution Tank (17).
3. Rotate the Solution Tank cap counter-clockwise to open.
4. Pour out the solution from the tank (17).Put back the Solution Tank
cap, screw it clockwise, then put the tank back in its place.
EN
58 CP 2000
EN
58 CP2000
1. Connect the steam cleaner into the mains. Press the power on/
off button, the indicator will light blue.
2. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
3. Put your foot on the head and angle the body of the cleaner downwards
(6).
4. Press the trigger to release the vapour (7).
5. Move the cleaner slowly backwards and forwards paying particular
attention to frequently used areas.
CARPET CLEANING
NOTE: Always vacuum or sweep the floor prior to use the steam cleaner.
IMPORTANT: Do not use the cleaner without the Textile Pad attached to
the Head.
1. Attach the Carpet Glider to the Head (10).
2. Connect the steam cleaner into the mains. Press the power on/off
button, the indicator will light blue.
3. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
4. Put your foot on the head and angle the body of the cleaner downwards
(6).
5. Press the trigger to release the vapour (7).
6. Move the cleaner slowly backwards and forwards paying particular
attention to frequently used areas.
MANUAL CLEANER OPERATION
1. Press the Manual Cleaner Release Button and remove the steel tube
(11).
2. Remove the Head (12).
3. Press the Water Tank Release Button and remove the Water Tank (3).
NOTE:A tube feeding water from the water tank to the boiler is loaded with
a brass ball. This design is intentional and serves to increase the efficiency
of water use. It is normal for this ball to create a rattling sound inside the
Water Tank during operation.
4. Pull the Water Tank by the cap and open it (4).
5. Fill the tank with cold tap water. Secure the tank with the cap (4). Do
not add any chemicals, detergents or perfumes to the Water Tank.
NOTE: We recommend to use distilled or de-mineralized water in order to
reduce building up mineral deposits and prolonging the life of the appliance.
EN
57CP 2000
6. Put the Water Tank back on the main part of the cleaner and make sure
the Water Filter is installed.
7. Connect the steam cleaner into the mains. Press the power on/
off button, the indicator will light blue.
8. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
9. Press the trigger to release the vapour (on the manual cleaner)(13).
IMPORTANT: Always disconnect the cleaner from the mains prior to
removing the Head or handling the appliance. Always ensure the cleaner
has fully cooled down before removing the Head.
SOLUTION TANK USE
1. Rotate the Solution Tank cap counter-clockwise to open and fill the tank
with a solution fluid (8).
2. Put back the Solution Tank cap and screw it clockwise.
3. Press the foot pedal to the ON position to engage the Solution Tank.
Press the foot pedal to the OFF position to disengage.
IMPORTANT:To prevent solution from leaking ensure the foot
pedal is in the OFF position when the product is not in use.
Empty the solution tank
1. Connect the steam cleaner into the mains. Press the power on/off
button, the indicator will light blue.
2. Remove the Solution Tank (17).
3. Rotate the Solution Tank cap counter-clockwise to open.
4. Pour out the solution from the tank (17).Put back the Solution Tank
cap, screw it clockwise, then put the tank back in its place.
EN
58 CP 2000
EN
59CP2000
• CAUTION! Use only distilled water to ll the water tank!
• Always unplug the appliance when lling with distilled water, emptying
or when the appliance is not in use.
REPLACING THE WATER FILTER
The water lter helps to lter minerals contained in water that reduce
the eciency of the steam cleaner. Depending on the frequency of use
of the appliance, the lter should be replaced every 80–100 hours. Use
only distilled water in the steam mop. If you live in an area with hard
water, this water may cause deposits on the heater, which will reduce the
performance of the cleaner. Use only distilled water. This will extend the
service life of the water lter and heater.
1. Connect the steam cleaner into the mains. Press the power on/
off button, the indicator will light blue.
2. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
3. Put your foot on the head and angle the body of the cleaner downwards
(6).
4. Press the trigger to release the vapour (7).
5. Move the cleaner slowly backwards and forwards paying particular
attention to frequently used areas.
CARPET CLEANING
NOTE: Always vacuum or sweep the floor prior to use the steam cleaner.
IMPORTANT: Do not use the cleaner without the Textile Pad attached to
the Head.
1. Attach the Carpet Glider to the Head (10).
2. Connect the steam cleaner into the mains. Press the power on/off
button, the indicator will light blue.
3. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
4. Put your foot on the head and angle the body of the cleaner downwards
(6).
5. Press the trigger to release the vapour (7).
6. Move the cleaner slowly backwards and forwards paying particular
attention to frequently used areas.
MANUAL CLEANER OPERATION
1. Press the Manual Cleaner Release Button and remove the steel tube
(11).
2. Remove the Head (12).
3. Press the Water Tank Release Button and remove the Water Tank (3).
NOTE:A tube feeding water from the water tank to the boiler is loaded with
a brass ball. This design is intentional and serves to increase the efficiency
of water use. It is normal for this ball to create a rattling sound inside the
Water Tank during operation.
4. Pull the Water Tank by the cap and open it (4).
5. Fill the tank with cold tap water. Secure the tank with the cap (4). Do
not add any chemicals, detergents or perfumes to the Water Tank.
NOTE: We recommend to use distilled or de-mineralized water in order to
reduce building up mineral deposits and prolonging the life of the appliance.
EN
57CP 2000
6. Put the Water Tank back on the main part of the cleaner and make sure
the Water Filter is installed.
7. Connect the steam cleaner into the mains. Press the power on/
off button, the indicator will light blue.
8. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
9. Press the trigger to release the vapour (on the manual cleaner)(13).
IMPORTANT: Always disconnect the cleaner from the mains prior to
removing the Head or handling the appliance. Always ensure the cleaner
has fully cooled down before removing the Head.
SOLUTION TANK USE
1. Rotate the Solution Tank cap counter-clockwise to open and fill the tank
with a solution fluid (8).
2. Put back the Solution Tank cap and screw it clockwise.
3. Press the foot pedal to the ON position to engage the Solution Tank.
Press the foot pedal to the OFF position to disengage.
IMPORTANT:To prevent solution from leaking ensure the foot
pedal is in the OFF position when the product is not in use.
Empty the solution tank
1. Connect the steam cleaner into the mains. Press the power on/off
button, the indicator will light blue.
2. Remove the Solution Tank (17).
3. Rotate the Solution Tank cap counter-clockwise to open.
4. Pour out the solution from the tank (17).Put back the Solution Tank
cap, screw it clockwise, then put the tank back in its place.
EN
58 CP 2000
EN
59CP2000
ENEN
5958 CP2000 | CP2010CP2000 | CP2010
… 30 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Concept CP2000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info