Bedienungsanleitung Concept VP8091 (Seite 25 von 59) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch)

802929

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

ENEN

4948 VP8090 | VP8091VP8090 | VP8091

CHECKING THE FULLNESS OF DUST BAG

If the dust bag full indicator is red during operation, replace the dust bag immediately.

Warning: if the suction power is low even after the dust container is emptied, there may be several reasons:

- some of the air passages (hose, telescopic tube, suction opening, brush attachment or other attachments) are

blocked,

- the motor ﬁlter is dirty,

- the air outlet ﬁlter is dirty.

Check each of these options and ﬁx the problem before using the appliance again. If you are unable to identify the cause

of the problem, take the appliance to your nearest service centre. Never use the appliance if the dust bag full indicator is

completely red during operation, you could irreparably damage the motor.

MAINTENANCE

Accessories and vacuum cleaner can be cleaned with a damp cloth. Never immerse the appliance in water! Do not use

aggressive substances such as solvents or abrasives for cleaning!

REPLACING THE DUST BAG

1. Unplug the appliance, pull the hose out of the suction opening and open the

vacuum cleaner cover.

2. Press the bag holder ﬂap and remove the dust bag (Fig. 3). Discard the paper or

SMS bag. Be careful not to tear it during handling. Only empty and close tightly the

textile bag - it can be reused.

3. Insert a new or emptied bag by sliding its board into the bag holder and lock it in

position with the ﬂap. The bag opening must be aligned with the opening for the

vacuum cleaner hose.

4. Always operate the appliance only if using a dust bag! If you forget to insert the

dust bag or you insert it incorrectly, the appliance motor may be damaged.

5. Close the cover and press it until it clicks.

REPLACING THE FILTERS

• The ﬁlters should be cleaned or replaced with visible soiling or when the suction

power of the vacuum cleaner drops. Check them after each use of the vacuum

cleaner.

• To avoid damaging the vacuum cleaner, do not use it without properly ﬁtted ﬁlters.

• Unplug the vacuum cleaner before replacing the ﬁlters.

• You can purchase suitable ﬁlter types from your dealer or order from the manufacturer.

CLEANING AND REPLACEMENT OF THE MOTOR FILTER

1. After disconnecting the ﬂexible hose, open the vacuum cleaner cover.

2. Pull the dust bag out of the holder for better access to the motor ﬁlter.

3. Remove the motor ﬁlter (Fig. 4). The ﬁlter can be cleaned by tapping. If heavily soiled, it can be washed in lukewarm

water and left to dry properly.

4. Insert a clean or new motor ﬁlter into the vacuum cleaner and close the vacuum cleaner cover.

Fig. 3

Fig. 4

CLEANING AND REPLACEMENT OF THE AIR OUTLET FILTER

1. Open the air outlet grille at the back of the vacuum cleaner (Fig. 5).

2. Remove the air outlet ﬁlter. This ﬁlter can be cleaned by mechanical tapping and

cleaning with a soft brush. A much soiled ﬁlter can be washed after this step and

cleaned with a soft brush in lukewarm water without detergents. It is important to

let the wet parts dry thoroughly. A wet ﬁlter would be depleted by vacuuming! Do

not use a hair dryer for drying!

Note: Wet cleaning can cause more wear on the ﬁlter and thereby shortening its

life.

3. Insert a clean or new air outlet ﬁlter into the vacuum cleaner and close the air

outlet grille.

TROUBLESHOOTING

Problem Cause Remedy

The motor is not working The plug inserted incorrectly or

insuﬃciently in the wall outlet.

Check connection of the plug.

The wall outlet is not energized. Check the presence of voltage, e.g.

with another appliance.

The motor stopped

working

Poor or too low airﬂow, thermal motor

protection has tripped.

Unplug the power cord. Check

and clear the intake and exhaust

air passage, ﬁlter cleanliness, and if

necessary, replace the dust bag. Allow

the vacuum cleaner to cool down.

The front cover cannot be

closed.

Dust bag incorrectly inserted. Check the dust bag insertion

Reduction of suction

power

Filled or clogged dust bag. Replace the dust bag.

Filter is clogged. Clean or replace the ﬁlter.

Clogged nozzle, tubes or hose. Check and clear the intake and exhaust

air passage.

The vacuum cleaner is

warming up

Warming up of the vacuum cleaner during operation is normal, it is not

amalfunction.

Fig. 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Concept VP8091 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info