652338
40
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
40 Operating the control software
Network Parameters Tab
The following network settings are used only for the communication via the
integrated BACnet IP interface.
IP Type: with this setting you determine whether you want to assign the IP
Address, the Subnet Mask, the Standard Gateway as well as the Primary
and Secondary DNS address as xed values or whether these should be
dynamically assigned via a DHCP server.
Note: after 5 unsuccessful attempts at obtaining an address with DHCP
the system will revert to xed assignment
Factory setting: DHCP
Options: DHCP (dynamic assignment)
Fixed (xed assignment)
IP Address: with this setting you manually enter the IP Address of the
Condair RS.
Note: This IP Address is used if "IP Type" is set (or reverts) to "Fixed".
Subnet Mask: with this setting you determine the Subnet Mask of the IP
network.
Note: This Subnet Mask is used if "IP Type" is set (or reverts) to "Fixed".
Default Gateway: with this setting you determine the IP Address of the
Default Gateway.
Note: This IP Address for the Default Gateway is used if "IP Type" is set
(or reverts) to "Fixed".
Primary DNS: with this setting you determine the IP Address of the Primary
Domain Name Server (DNS).
Note: This IP Address for the Primary Domain Name Server is used if "IP
Type" is set (or reverts) to "Fixed".
Secondary DNS: with this setting you determine the IP Address of the
Secondary Domain Name Server (DNS).
Note: This IP Address for the Secondary Domain Name Server is used if
"IP Type" is set (or reverts) to "Fixed".
MAC Address: factory set MAC Address (Media Access Control) of the
Condair RS. Not modiable.
Host Name: Host Name of the Condair RS automatically generated by
the control. Format: "IC_"+"Serial number of the device". Not modiable.
BMS Timeout Tab
BMS Timeout: with this setting you determine the maximum time the
humidier will wait with no communication from the BMS network before
a BMS timeout warning is generated. Exceeding the timeout also stops
humidier operation if the signal source of the humidier is set to a BMS
input.
Factory setting: 300 s
Setting range: 1 ... 300 s
40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Condair RS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Condair RS

Condair RS Installationsanweisung - Englisch - 80 seiten

Condair RS Bedienungsanleitung - Holländisch - 80 seiten

Condair RS Installationsanweisung - Holländisch - 76 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info