Bedienungsanleitung Constructa CG563J7 (Seite 23 von 26) (Englisch)

596602

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Installation

The dishwasher must be connected by

a qualified technician to ensure correct

operation. The specifications for supply,

drainage and connected load must fulfil

the required criteria as stated in the

following paragraphs or in the installation

instructions.

Install the appliance in the following

sequence:

– Check the delivery

– Install the appliance

– Connect the waste water

– Connect the fresh water

– Connect the power supply

Delivery

Your dishwasher was checked at the

factory to ensure that it was in perfect

working order. This may have left some

small water stains in the dishwasher.

These will disappear after the first rinse

cycle.

Installation

The required installation dimensions can

be found in the installation instructions.

Using the height-adjustable feet, adjust the

appliance until it is level. Ensure that the

appliance is standing firmly.

Waste water connection

See the installation instructions for the

required connection steps. If required,

attach a siphon with drainage spigot.

Using the enclosed parts, connect the

waste water hose to the drainage spigot

of the siphon.

Ensure that the drainage hose is not

kinked, crushed or twisted (ensure that

there is no sealing cover which prevents

the waster water from flowing away!).

Fresh water connection

Using the enclosed parts, connect the

fresh water connection to the tap

according to the installation instructions.

Ensure that the fresh water connection is

not kinked, crushed or twisted.

When replacing the appliance, always

connect a new water supply hose to the

water supply. The old supply hose must

not be re-used.

Ensure that the fresh water connection is

not kinked, crushed or twisted.

Water pressure:

Minimum 0,5 bar – maximum 10 bar.

If the water pressure is higher, install a

pressure reducing valve.

Flow rate:

Minimum of 10 litres per minute.

Water temperature:

We recommend that you use cold water.

If you do use hot water, the temperature

should not exceed 60 °C.

Electrical connection

This appliance should only be connected

to a 230/240 V AC source via a properly

installed earthed socket. See nameplate

31 for size of required fuse.

The socket must be installed close to the

dishwasher.

If the domestic wiring includes a residual-

current-operated (FI) circuit-breaker, make

sure that it bears the

mark, as only

this type conforms to the latest regulations

Disconnecting the dishwasher

Here too, it is important that tasks are

carried out in the correct sequence:

always unplug the appliance from the

mains electricity first of all.

Pull plug out of wall socket.

Turn off water supply.

Disconnect drain and water input hoses.

Remove screws in underside of work

surface. Detach base board, if fitted.

Pull out appliance and carefully withdraw

hoses at same time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Constructa CG563J7 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Constructa CG563J7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info