Bedienungsanleitung Corally 10SL (Seite 17 von 22) (Englisch)

639721

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

MAINTENANCE AND SETUP TIPS.

Tweak (left to right balance of the car).

One of the most important factors when racing an R/C on-road car is ‘tweak'. If a car is tweaked then the car will turn differently in left and right

hand bends. Purposely tweaking a car may be advantageous when oval racing, but generally it is best if the car handles exactly the same in both

left and right hand turns.

A car becomes tweaked when the grip or weight is not balanced between left and right hand wheels. This may occur in several ways.

- The chassis assembly could be twisted, this is no longer common in modern cars, but should be checked after major crashes.

- The tires on each side of the car could be different sizes. The outside tire generally wears more quickly than the inside tire. To prevent

problems swap the tires from left to right hand sides after every couple of races. Or use a tire truer if available.

- The suspension or ride height may not be set the same on each side of the car. Check springs, tweak adjuster settings and ride height settings.

- Steering movement may be different on left and right sides.

- Tires may be giving different grip levels. Check and replace any that seem to have different firmness on the left or right.

- When using tire additive it is possible to tweak the car by accidentally applying different amounts of additive to each tire – be careful!

- Finally its possible for the car to feel tweaked if the suspension does not move freely. Check that the power wires to the motor do not restrict

the rear suspension movement and check that all ball joints move freely.

Ride height adjustment.

The ride height should be kept to a minimum, this will keep the centre of gravity of the car as low as possible and so maximise cornering speeds.

The ride height should ideally be between 4 – 6 mm (1/8"-3/16"), but on bumpy tracks or where regulations dictate otherwise run the car a little

higher. Check regularly to compensate for tire wear which can be rapid on some tracks.

Adjusting the front ride height.

A-arm spacers cab be mounted under A-arms of the front suspension. Placing the front A-arms block lowers the chassis (less ride height) and

conversely putting them above raises the chassis, giving more ride height.

Adjusting the rear ride height.

Three molded different pairs of rear axle bearing holders have been included in the kit, they are all off-set to give 6 different rear axle height

settings. Optional Available are six pairs of rear axle Hard Anodised Aluminium bearing holders. With these settings it is possible to fine tune the

ride height with different kind of tire sizes.

Remove the rear axle and fit the appropriate pair of bearing holders to each end of the rear axle tube, complete with ball bearings and put the

rear axle back into place. Do not forget to re-mesh your pinion and spur gear. Always use the same height setting on both sides of the car

otherwise the rear axle bearings will lock up.

Rear tube damper servicing and adjustment.

The rear tube dampers are a very important part of the car. These dampers control the rear suspension movement.

Periodically check that the movement of these dampers is even and smooth in all directions. To change the damper action (stiffness) the damper

syrup has to be replaced by another type. Corally offers 3 different grades as following:

#80000 – Damper Syrup, Soft

#80001 – Damper Syrup, Hard

#80002 – Damper Syrup, X-Hard

Rear damper setup.

The rear damper setup controls the speed at which the rear suspension moves over bumps and through turns.

- If the car is poor over bumps then increasing the rear dampening effect may help.

- Increasing the rear dampening effect will also increase steering a little, remember this when making this adjustment for other reasons.

- If the inside front wheel goes light or even lifts during cornering then the damper is to thin.

- If the car is reluctant to change direction quickly enough in chicanes then reducing the rear damper effect may help.

General rule - if the car understeers whilst exiting corners then the rear damper is set too thin. If the car oversteers exiting corners then the

damper is too thick.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Corally 10SL Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info