Bedienungsanleitung Corbero CLV6600W (Seite 15 von 30) (Englisch)

751431

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

EN - 11

Continued use of too much detergent may

cause machine damage.

Using little detergent can result in

poor cleaning and you can see whitish

streaksin hard water. See the detergent

manufacturer’s instructions for a further

information.

4.9. Filling the detergent

Push the latch to open the dispenser and

pour in the detergent.

Close the lid and press it until it locks in

place. The dispenser should be refilled just

before the start of each programme. If the

dishes are heavily soiled, place additional

detergent in the pre-wash detergent

chamber.

DETERGENT

4.10. Using combined detergents

These products should be used according

to the manufacturer’s instructions.

Never put combined detergents into the

interior section or the cutlery basket.

Combined detergents contain not only

the detergent but also rinse-aid, salt

replacement substances and additional

components depending on the combination.

We recommend you do not use combined

detergents in short programmes.

Please use powder detergents in such

programmes.

If you encounter problems when using

combined detergents, please contact the

detergent manufacturer.

When you stop using combined detergents,

make sure that water hardness and rinse

aid settings are set to the correct level.

4.11. Rinse-aid usage

The rinse aid helps to dry the dishes without

streaks and stains. Rinse-aid is required for

stain-free utensils and clear glasses. The

rinse aid is automatically released during

the hot rinse phase. If rinse aid dosage

setting set too low, whitish stains remains

on dishes and dishes do not dry and

washed clean. If rinse aid dosage setting

set too height, you can see bluish layers on

glass and dishes.

4.12. Filling the rinse-aid and setting

To fill the rinse aid compartment, open

the rinse-aid compartment cap. Fill the

compartment with rinse aid to the MAX level

and then close the cap. Be careful not to

overfill the rinse aid compartment and wipe

up any spills.

In order to change the rinse aid level,

follow the below steps before turning on

the machine:

• Push the programme button and hold it

down.

• Turn on the machine.

• Hold down the programme button until

“rA” disappears from the display. Rinse

aid setting follows water hardness

setting.

•

Set the level by pushing the “+” and “-”

buttons.

Switch off the machine to save the

setting.

The factory setting is “4”.

If the dishes are not drying properly or are

spotted, increase the level. If blue stains

form on your dishes, decrease level.

Level Brightener Dose Indicator

1 Rinse-aid not

dispensed

r1 is shown on the

display.

2 1 dose is

dispensed

r2 is shown on the

display.

3 2 doses are

dispensed

r3 is shown on the

display.

4 3 doses are

dispensed

r4 is shown on the

display.

5 4 doses are

dispensed

r5 is shown on the

display.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Corbero CLV6600W Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Corbero CLV6600W

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info