Bedienungsanleitung Cosatto Giggle 2 (Seite 5 von 31) (Englisch, Spanisch)

768916

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

8 - erecting the carrycot - stage 1

Remove the mattress and liner from the cot (a). (The liner is retained by a strip of Velcro® at the top).

Open the lining at the base of the cot and slide the frame bars, using the straps (b), until the ‘V’

sections on the frame bars fit into the cutouts in the cot base (c).

Reattach the Velcro® strip to complete the step.

9 - erecting the carrycot - stage 2

Refit the liner into the carrycot and secure with the Velcro® strips at the top.

Place the mattress over the liner at the base of the carrycot.

10 - fitting and using the carry handle

To fit the carry handle push each end into the carrycot mountings until the buttons lock the handle

in place (a).

To open the carry handle press the button on one side of the handle (b) and lift the handle end

clear of the mounting (c).

Repeat this procedure at the other end of the handle to remove the handle from the carrycot.

11 - fitting the carrycot

Place the carrycot on to the mounting points on each side of the chassis (a). Push down until the

tab locate in the holes of the carrycot mountings (b).

Note: The carrycot can only be fitted rearward facing as shown in illustration. Dots are marked on

the seat mounts and carrycot mounts (c). These should be on the same side and aligned if fitted

correctly.

There are a set of “D” ring located at the base of the carrycot for the attachment of a separate

safety harness approved to BS EN 13210 should this be required (harness not supplied). Push the

‘D’ rings through the lots in the liner (d).

12 - removing the carrycot

To remove the carrycot from the chassis, press the buttons on each side of the mountings (a) then

lift the carrycot free (b).

Note: Please ensure that the carry handle is securely fitted before lifting the carrycot clear of the chassis.

13 - opening and closing the carrycot hood

Pull the hood up to open (a). Push the hood back down to close (b).

14 - removing the carrycot hood

To remove the carrycot hood, pull the lip at the bottom of the hood mount (a) and pull the hood away.

To re-fit the hood place the top of the hood mount (b) over the chassis frame and then push hard

on the bottom (c) until the hood mount clips in place. Attach the Velcro® tabs (d) on both sides.

15 - fitting the carrycot apron

Lay the cot apron over the carrycot and attach the zip to the liner (a). Pull the zip around the cover

until secure. Place the bib of the cot apron inside of the hood on either side of the hood as shown (b).

Removal of the cover is a reversal of this procedure.

16 - fitting the raincover in pram mode

Fit the raincover over carrycot as shown. The air holes in the raincover should be just in front of the

hood on either side (a).

The cutouts in the raincover fit over the carrycot mounts. Secure with the Velcro® straps (b).

17 - fitting and removing the seat unit

Place the seat unit on to the mounting points on each side of the chassis. Push down until the

tabs locate in the holes of the seat mountings (a).

To remove the seat unit from the chassis, press the buttons on each side of the mountings (b) then

lift the seat unit free (c).

Note:

The seat unit can be fitted facing forwards or backwards.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cosatto Giggle 2 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info