Bedienungsanleitung Cosatto Ooba (Seite 5 von 50) (Englisch, Französisch, Spanisch)

768917

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

7 - adjusting the height of the handle

Press the button (a) in the centre of the handle and lift the handle (b) or lower the handle (c) as

required. Release the button when the handle is in the desired position.

8 - reversing the handle position

The handle position can be reversed. This is useful if the pushchair is used on uneven ground. As

this may make the pushchair harder to steer so Cosatto recommend returning the handle to its

original position for use on a flat surface.

To reverse the handle position, simultaneously lift the levers (a) and push the handle forward (b)

until a “click” is heard and the handle is locked in the reverse position.

Note: The handle will need to be raised (See step 7) if the seat unit is fitted.

9 - folding the chassis

Before folding the chassis ensure the front wheel swivel locks are released (See Step 5).

Ensure the handle is not in the reversed position. When first folded the handle should locate

between the large wheels (d).

Press the button (a) in the centre of the handle and push the handle down (b) to its lowest position.

Simultaneously lift the levers (c) then push the handle down (d) as far as it will go.

Push the folding button, marked with a 1, with your thumb (e) whilst lifting the folding handle,

marked with a 2, (f). Lift the chassis off the floor slightly to allow the front legs to fold inwards (g)

to complete folding process.

10 - erecting the carry cot

Slide the frame bars, using the straps (a), until the frame bars fit into the cut-outs in the carry cot

base (b).

Fit the carry cot liner to the carry cot by attaching the zip fasteners (d & e). Note: The carry cot has

two sets of zips around the top edge. Fit the carry cot liner to the lower zip. The top zips are for the

carry cot apron and the carry cot hood.

Place the mattress in the carry cot (f).

Turn the carry cot mountings downwards (g) until they lock in place.

11 - fitting and removing the carry cot

Place the carry cot on to the mounting points on each side of the chassis. Push down (a) until a

“click” is heard and the mountings are locked in place.

Note: The carry cot can only be fitted rearward facing.

To remove the carry cot from the chassis, press the buttons on each side of the mountings (b) then

lift the carry cot free (c).

12 - using the carry cot

Zip the carry cot apron to the carry cot (a) and secure both ends of the apron flap (b) to the hinge

by fasten the press studs.

To lift the carry cot hood press the buttons (c) on each hinge then lift the hood upwards (d).

To lower the hood, press the buttons (e) on each hinge then push the hood downwards (f).

The frame at the top of the hood can be used as a carrying handle (g).

13 - fitting the carry cot raincover

Lay the raincover over the carry cot as shown. Attach the fastener straps under the pushchair handle

hinge (a).

There is a flap on top of the raincover to allow access to the carry cot handle (b).

Unfasten the zips around the raincover to allow access to inside the carry cot (c). Refasten the zips

to close the raincover insuring the zips meet centrally at the top of the handle (d).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cosatto Ooba Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info