Bedienungsanleitung Cramer 82CS15 (Seite 11 von 309) (Alle Sprachen)

818993

Zoom out

Zoom in

Vorherige Seite

1/309

Nächste Seite

cramer.eu

and do not operate this product until all missing or damaged parts are replaced.

Please call Customer Service for assistance.

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to

damage from various types of commercial solvents and may be damaged by their

use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING!

Do not at any time let brake liquids, gasoline, petroleumbased

products, penetrating oils, etc.,come in contact with plastic parts.

Chemicals can damage, weaken or destroy plastic which may

result in serious personal injury.

Only the parts shown on the parts list are intended to be repaired or replaced by

the customer. All other parts should be replaced at an authorised service centre.

STORAGE

Storing the product

•Remove the battery pack from the unit before storing.

•Clean all foreign material from the unit.

•Store it in a place that is inaccessible to children.

•Keep away from corrosive agents such as garden chemicals and de-icing

salts.

•Store and charge your batteries in a cool area. Temperatures above or below

normal room temperature will shorten battery pack life.

•Never store batteries in a discharged condition. Store battery packs in a

30%- 50% charged condition.

•Store the battery pack where the temperature is between 0-23* C and

away from moisture.

•All batteries gradually lose their charge. The higher the temperature, the

quicker they lose their charge. If you store your unit for long periods of time

without using it, charge the pack as normal every six months of storage.

This practice will prolong battery pack life.

Troubleshooting

PROBLEM PROBABLE CAUSE POSSIBLE SOLUTION *

Bar and

saw chain

running

hot and

smoking.

Check saw chain tension for

overtightened condition. Tension saw chain.

No oil in the oil tank. Reﬁll oil into the oil tank.

The discharge port is

blocked by debris.

Refer to the manual to remove

the bar and clean out the debris.

Oil tank is blocked by

debris.

Clean out the oil tank and reﬁll

with clean oil.

Bar and chain oil tank cap is

blocked by debris. Clean the debris off the oil cover.

The sprocket or guide wheels

is clogged with debris.

Clean and remove debris from

sprocket and guide wheel.

Motor

runs, but

chain is not

rotating.

Saw chain tension is too

tight.

Refer to Saw Chain Tension

Guide earlier in this manual.

Check guide bar and saw

chain assembly.

Refer to Replacing the Bar and

Saw Chain assembly earlier in

this manual.

Check guide bar and saw

chain for damage.

Remove the battery from the

unit. Take the bar cover off,

and remove the bar and saw

chain. Clean all debris from the

chain saw. After all debris is

cleared, insert battery and run

the chain saw. If the sprocket is

spinning your motor is okay. If

the sprocket is not spinning, call

customer service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cramer 82CS15 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info