818994
4
Zoom out
Zoom in
Vorherige Seite
1/236
Nächste Seite
1 DESCRIPTION
1.1 PURPOSE
This chainsaw is designed for cutting branches, trunks,
logs and beams of a diameter determined by the cutting
length of the guide bar. It is only designed to cut wood.
1.2 OVERVIEW
Figure 1-22
1Guide bar cover
2Front handle
guard / chain brake
3Front handle
4On/Off switch
5Lock out button
6Trigger
7Oil tank cap
8Oil indicator
9Spike bumpers
10 Saw chain
11 Guide bar
12 Rear handle
13 Chain tension
screw
14 Chain cover
15 Chain cover nuts
16 Bolt for saw chain
tension
17 Sprocket
18 Battery release
button
19 Oil outlet
20 Bar groove
21 Chain drive links
22 Cutter
23 Felling direction
24 Danger zone
25 Escape route
26 Direction of fall
27 Notch
28 Felling back cut
29 Hinge
30 Limb cut
31 Keep work off
ground leave
support limbs until
log is cut
32 Log supported
along the entire
length
33 Cut from top (over
buck) avoid cutting
earth
34 Log supported one
end
35 Under buck
36 Over buck
37 Log supported both
ends
38 Bucking a log
39 Stand on uphill
side when cutting
because log may
roll
40 Wrench
2 GENERAL SAFETY
WARNINGS
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this machine.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
3 INSTALLATION
WARNING
Do not change or use accessories that are not
recommended by the manufacturer.
WARNING
Do not install battery pack until you assemble all the
parts.
3.1 UNPACK THE MACHINE
WARNING
Make sure that you correctly assemble the machine
before use.
WARNING
If parts of the machine are damaged, do not use
the machine.
If you do not have all the parts, do not operate the
machine.
If parts are damaged or missing, contact the
service center.
1. Open the package.
2. Read the documentation provided in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and packing material in compliance
with local regulations.
WARNING
For your personal safety, do not insert battery before
the tool is assembled completely.
3.2 ADD THE BAR AND CHAIN
LUBRICANT
Examine the amount of oil in the machine. If the oil level
is low, add the bar and chain lubricant as follows.
IMPORTANT
Use bar and chain lubricant that is only for chains and
chain oilers.
NOTE
The machine comes from the factory without bar and
chain lubricant.
4
English
EN
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Cramer 82CS24 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info