Bedienungsanleitung Cramer 82LT107 (Seite 14 von 340) (Alle Sprachen)

818974

Zoom out

Zoom in

Vorherige Seite

1/340

Nächste Seite

Error Code Description Solution

NA Display communication error Please check the display's connecting parts and CAN net-

work.

Incorrect display selected Please select the correct display for your vehicle model

7 MAINTENANCE

7.1 MOWER BLADE MAINTENANCE

Check the mower blades daily. They are the key to power efficiency and well-groomed turf. Keep them sharp -- a dull

blade will tear rather than cut the grass, leaving a brown ragged top on the grass within a few hours. A dull blade also

requires more power. Replace any blade that is bent, cracked or broken.

WARNING

Never attempt to straighten a bent blade by heating, or weld a cracked or broken blade as the blade may break and

cause serious injury. Replace worn or damaged blades.

WARNING

Never work with blades while key is in the ignition switch. Turn key to “OFF” position, remove the battery packs

from the machine. Block up mower when you must work under it. Wear gloves when handling blades. Always check

for blade damage if mower strikes a rock, branch or other foreign objects!

DANGER

Touch-up sharpening can be done with a file. Check the blades for balance following grinding. A commercial

balancing tool is available through most hardware supply stores, or balancing can be done by placing the blade on

an inverted line punch or 12.7mm (1/2") bolt. Blade should not lean or tilt. While spinning the blade slowly, it should

not wobble. If blade is out of balance, true it up before reinstalling. Lay the blade on a flat surface and check for

distortion. Replace any distorted blade.

WARNING

• The blade sail (curved part) must be pointing upward toward the inside of the deck to ensure proper cutting.

• When mounting blades, rotate them after installation to ensure blade tips do not touch each other or sides of the

mower.

• Failure to correctly torque the bolt may result in the loss of the blade, which can cause serious injury.

• Mower blades are sharp and can cut. Wear gloves and use extra caution when servicing them.

7.1.1 REPLACE THE BLADE

See figure 17

1. Stop the motor, remove the start key, and set the parking brake.

2. Raise the height of the cutting deck to its highest position to allow access to blades.

NOTE

If necessary, raise the mower by placing on a lift or using a jack and jack stands, or remove the cutting deck as

described in the previous section to gain access to the blades.

WARNING

If raising the mower to access the blades, make sure the mower is properly secured and the parking brake is

set before proceeding. Failure to properly secure the mower could cause it to fall, resulting in death or possible

serious personal injury.

3. Wedge a block of wood between the blade and mower deck to prevent the blade from turning.

4. Loosen the blade nut by turning it counterclockwise (as viewed from bottom of mower) using a 16 mm wrench or

socket (not provided).

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cramer 82LT107 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info