Bedienungsanleitung Creda T632CW (Seite 11 von 24) (Englisch)

498215

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

The Controls - Excel Sensor Dry Models (continued)

(iii) Timed Drying

(iv) Speedy Iron

Cycle

Starting a

Programme

(Green Active

light)

Empty Water light

The ‘Cool Tumble’

phase

A short programme of around 30 minutes is provided to dry small loads

of less than 1kg.

To select this programme, turn the knob clockwise until 30 min

appears in line with the indicator. About 10 minutes before the pro-

gramme is completed, the heating elements are switched off and the

programme enters the final ‘Cool Tumble’ phase.

This is a short programme of approximately 10 minutes to condition

previously dried clothes. See section ‘Speedy Iron Programme’.

It consists of a period of heating followed by a short cool tumble

period (as detailed below).

Select High heat for this programme.

It should not be used on damp loads, as it is NOT a drying

programme.

Press the Start button and the indicator light turns Green to show that

the programme is active. The light goes out when the selector is

returned to position ‘0’, or if the door is opened during the

programme’s duration.

CAUTION:

If the door is opened during the cycle, the dryer stops automatically.

When the door is closed the Start button must be pressed to restart the

programme. The light flashes green to remind you to press the Start

button. The cycle resumes from the point it stopped, if the position of

the knob has not been changed. Otherwise, the dryer starts the new

selection.

The indicator light turns Orange during a drying programme when the

water container is full. When this happens, you must empty the water

container. You should not wait for this light to change colour before

emptying the container, but empty it after each load (see section

‘Emptying the Water Container’).

The programme goes directly to the cool tumble phase and the dryer

stops. The Orange light warns you that the load will not be dried

correctly.

At the end of a drying programme if the container has filled the

indicator light will glow Red. Empty the water container and start the

programme again by pressing the Start button.

The indicator light goes off (or turns Green if a programme is running)

about 10 seconds after the water container has been put back.

About 10 minutes before the programme is completed, the heating

elements will be switched off, the programme enters the final ‘Cool

Tumble’ phase. During this period, the fabric is cooled. You should

always allow the dryer to complete this phase. By opening the door,

you can check the dryness of the load as often as you wish and if you

want to, remove some items before they are fully dry. (This is

particularly useful for a mixed load when you want to iron some items,

but others to be fully dried). You will need to press the Start button

after closing the door to re-start the programme.

THE START BUTTON MUST BE PRESSED TO START ALL

PROGRAMMES INCLUDING A DELAYED START (DRY LATER)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Creda T632CW Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info