Bedienungsanleitung Creda TCS3 (Seite 4 von 16) (Englisch)

498211

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Moulded plug

! The plug must not be used without

the fuse cover in place.

If a replacement fuse holder/cover

is required, it must be of the same

colour coding or wording as shown

on the base of the plug.

Replacements are available from

authorised dealers.

Changing the plug

The wires in the power cord are coloured in accordance with

the following:

! If the plug being replaced is a non-rewirable type, then

the cut-off plug must be disposed of safely. DO NOT leave

it where it can be inserted into a socket and create a shock

hazard.

! The power supply cord should be checked periodically and

replaced by a cord specially prepared for this dryer and fitted

only by authorised technicians (see Service). New or longer

power cords are supplied at an extra charge by authorised

dealers.

! The manufacturer denies any responsibility should any of

these rules not be followed.

! If in doubt about any of the above consult a qualified

electrician.

Before you start using your dryer

Once you have installed your dryer and before you use it,

clean the inside of the drum to remove any dust that could

have accumulated during transport.

! Keep this instruction booklet on hand in order to refer to it

when necessary. Take it with you when you move, and

should you sell this appliance or pass it on to another

party, make sure that this booklet is supplied along with

the dryer so that the new owner may be informed about

warnings and suggestions on how the dryer works.

! Read these instructions carefully; the following pages

contain important information on installation and

suggestions on how the appliance works.

Door Reversal Instructions

The door of your dryer is reversible and can easily be

changed. Exchange diagonally hinge brackets and

blanking screws. Exchange door latch and catch with their

opposite blanking plates (see diagram above).

Where to put your dryer

●

Place your dryer at a distance from gas ranges,

stoves, heaters, or cook tops because flames can

damage the appliance.

●

If you are going to install the appliance under a work

counter, be sure to leave a 10mm space between the

top and any other objects on or above the machine

and a 15mm space between the sides and lateral

furnishings or walls. This is to ensure proper air circulation.

Make sure that the back vents are not obstructed.

Ventilation

When the dryer is in use, there has to be adequate

ventilation. Make sure you put your dryer in an environment

that is not damp and has proper air circulation throughout.

Airflow around the dryer is essential to condense the

water produced during the washing, the dryer will not

operate efficiently in an enclosed space or cupboard.

! If using the dryer in a small or cold room some

condensation could be experienced.

Water drain

If your dryer is installed next to a drain the water can be

plumbed into this drain. This does away with the need to

empty the water container. Simply remove the top hose

from its top fitting at the rear of the dryer and plumb the

hose provided to the drain.

Electrical connections

Make sure of the following before you insert the plug into

the the electrical socket:

●

The socket must be grounded.

●

The socket must be able to sustain the machines

maximum power, which is indicated on the rating label

(see Dryer Description).

●

Power voltage must be within the values indicated on

the rating label (see Dryer Description).

●

The socket must be compatible with the dryers plug.

Should this not be the case, replace the plug or the socket.

! The dryer must not be installed outdoors, even if the space is

sheltered. It can be very dangerous if it is exposed to rain

or storms.

! Once installed, the dryers electrical wire and plug must

be within easy reach.

! Do not use extension cords.

! The power cord must not be bent or squashed.

! The power cord supplied is fitted with a BS1363 plug and a

13 amp BS1362 fuse. If you need to replace the fuse, use only

those rated at 13 amp (13A) and ASTA approved to

BS1362.

Door catch

Door latch

Hinge

Green and Yellow

(Earth) wire to terminal

marked ‘E’, symbol ,

or coloured green and

yellow.

13A ASTA approved

fuse to BS1362.

Brown (Live) wire to

terminal marked ‘L’ or

coloured red.

Blue (Neutral) wire to

terminal marked ‘N’ or

coloured black.

Cord clamp

Installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Creda TCS3 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info