Bedienungsanleitung Crivit 1-LD3604-3 IAN 94528 (Seite 35 von 38) (Deutsch, Englisch, Holländisch)

736591

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

Notes on the BMI

The BMI is a statistical measurement that can be used to judge a persons weight.

For adults, a value between 18.5 and 25 is considered normal. Values below

18.5 are considered "underweight". Values above 25 are considered

"overweight". Values above 30 are considered "Obese".

The BMI is only a coarse guideline because it does not take a persons body type

and body composition into consideration.

Heart rate

(PULS/HRM)

If the chest belt is worn the current heart rate will appear on the bottom row of the

display.

Timer

(TIMER)

The bottom row of the display will show the elapsed time. The value can be reset

by pressing and holding SET.

Distance

(DISTANZ/DISTANCE)

The bottom row of the display will show the covered distance. The value can be

reset by pressing and holding SET.

Average speed

(DURCH-GESCHW/AVG SPEED)

The bottom row of the display will show the average speed. The value can be

reset by pressing and holding SET.

Maximum speed

(MAX GESCHW/MAX SPEED)

The bottom row of the display will show the maximum speed. The value can be

reset by pressing and holding SET.

Troubleshooting

The distance measurements are very imprecise

The watch uses the step length measured during calibration to estimate the

traveled distance.

Recalibrate the step counter. Calibrate it for walking and for running and use extra

care during the calibration.

Running on uneven surfaces may also result in bad calibration.

The heart rate is not shown or is shown incorrectly

Make sure the chest belt is positioned correctly and fits well

Your skin should not be too dry or too cold.

The contact areas can be slightly moistened to improve function

Electromagnetic interference may have an adverse effect on reception

The distance between watch and chest belt must be under 60cm

Other heart rate measuring devices within a 2m range may also cause

interference.

Wireless bicycle computers may cause interference

The batteries may be low and require replacing

The display is unreadable / the light does not work

Replace the batteries

Replacing the watch battery

The battery replacement can be performed by a watch maker in addition to a

water resistance test. To replace the battery yourself, please read the following

instructions first:

Remove the screws (1, 2, 3 and 4) from the back side of the watch with a small

Phillips screwdriver. Remove the caseback and the battery sticker. Use a small, flat

tool to open the latch (5) of the battery holder. Remove the battery and insert a

fresh 3V CR2032 battery with the (+) terminal facing upwards. Ensure that the

gasket (6) is seated correctly. Close the latch of the battery holder. Replace the

battery sticker and the caseback and replace the screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crivit 1-LD3604-3 IAN 94528 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Crivit 1-LD3604-3 IAN 94528

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info