Bedienungsanleitung Crivit 1-LD4657 - IAN 285498 (Seite 17 von 72) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

732011

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Incorrectly performing the calibration can

result in faulty measurements. When

encountering "suspicious" or incorrect

readings, the calibration should be

repeated.

Entering the deviation (declination) to the

geographical North Pole

This deviation results from the calculable

difference between the magnetic North Pole

and the geographical North Pole as used

on maps. The local deviation is printed on the border of geographical maps (the

deviation depends on the latitude). It is shown as a positive east value (E) or a

negative west value (W). When using the map to navigate to a target, the direction

to the target must be adjusted on the map. This is done by subtracting the positive

value or adding the negative value to the shown value.

Press and hold SET to enter the declination mode.

Immediately after entering the setting mode for the

declination, the letter "E" (for east) will blink on the display. Press SEL to select E or

W (for west). Press SET to confirm your selection.

The degree digits will blink on the display. Press SEL to enter the declination and

press SET to confirm your setting.

Because the entered values directly influence the directional indication, they must be

activated by pressing SEL to select " ON" or „ OFF“. Confirm your selection by

pressing SET.

Exit setting mode by pressing MODE.

The following examples may help to explain the effect of the deviation:

The direction shown on the display is N10° (10 degress north).

Entering an east deviation (E) of 30 degrees will change the directional indication to

NE (north-east) 40 degrees.

Entering a west deviation (W) of 30 degrees will change the directional indication

to NW (north-west) 340 degrees.

Altimeter (ALTI)

(-999 m - +9999 m / -2999 ft - +29999 ft)

Please note:

Your altitude is determined by measuring

atmospheric air pressure. The shown value can vary by up to

50 m because of changing weather- regardless of a change

in location.

We recommend that, before use, the altitude value should be

set with the sports watch on your wrist. Then wait for a few

minutes so that the value can stabilize.

Select the feature by pressing MODE repeatedly. Press SEL to select the different

sub-features.

Altimeter (ALTI) > maximum altitude memory (HIGH) > minimum altitude memory

(LOW) > total altitude gain (UP) > total altitude loss (DOWN) > number of hills

(HILL) > memory (RECORD).

Height

Press SEL to select the sub-feature (ALTI).

Press and hold SET for 3 seconds to enter setting mode. Enter the

desired value by pressing SEL and confirm your setting by pressing

SET.

Exit setting mode by pressing MODE.

Press SET to select the display mode height/time or

temperature/time/diagram/current altitude.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crivit 1-LD4657 - IAN 285498 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info