Bedienungsanleitung Crivit 7769 11500 000 IAN 46862 (Seite 8 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

736610

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

9 GB/IE

Operation / Tips for the best cooling ... / Exchanging ... / Possible malfunctions

temperature) of up to 17 °C and thereby a lower

inside temperature than is possible in the “eco” nor-

mal operation, turn the cooling output switch

the “MAX” position. Please note that in this case

more energy will be consumed than in normal

operation.

After the operation with 230 V function has been

completed, disconnect the mains plug from the

socket.

Function with 12 V operation

CAUTION! The temperature controller on the

front of the lid is only suited to 230 V operation

and it does not function in 12 V operation.

When operating with a 12 V power supply, the

cooling unit always produces a temperature

diﬀerence from the ambient temperature of up

to 17 °C. The cooling output can not be con-

trolled by means of the temperature controller

on the front of the lid.

Tips for the best cooling output

and energy saving

Select a well ventilated location protected from

sunshine.

Only place pre-cooled contents into the cool-

box.

Do not open the coolbox longer than necessary.

Don’t leave the lid open longer than necessary.

Ensure that the coolbox is not packed too

full and that the air can circulate adequately

between the coolbox contents.

In order that a high level of energy saving can

be achieved, normal operation (cooling output

switch

in the “eco” position) is recom-

mended for longer periods of use in 230 V

operation.

Exchanging the 12 V fuse

See also ﬁg. C.

To replace the 12 V fuse

, unscrew the red

adjustment sleeve

from the plug, turning

counter-clockwise.

Unscrew the screw

with a suitable Phillips

screwdriver from the top half of the housing

Lift the top half

of the housing from the bot-

tom half

Lift the contact pin

carefully out of the hous-

ing section. The fuse

can now be removed.

Note: If the thin metal connection in the mid-

dle between the two metal caps is broken, then

the fuse

is defective and must be replaced.

Press the contact spring

backwards and

insert the new fuse

carefully into the groove

provided for it. Now place the rear edge of the

contact pin

on the front metal cap of the fuse

. By releasing the contact spring

, the fuse

and contact pin

are located in the groove.

Screw the top and bottom halves of the housing

together again, reattach the red

adapter sleeve

and turn clockwise to tighten.

The plug is now ready for operation.

Possible malfunctions

Firstly check whether you have correctly followed

the instructions for using the coolbox, then also

check:

– Is the connection cable correctly connected

and does your car cigarette lighter / domestic

socket function properly?

– Have you set up the coolbox in such a way

that the air can circulate freely and that venting

of the cooling unit can occur?

– Is the fuse in the plug of the 12 V connection

cable OK?

– Check the position of the cooling output

switch

on the front of the lid.

If you can not rectify the malfunction on your own,

please contact our Customer Service (see chapter

on “Service”).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crivit 7769 11500 000 IAN 46862 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info