Bedienungsanleitung Crivit BS-2418 IAN 277828 (Seite 9 von 30) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

736859

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

11GB/IE

Prevent property damage!

• Avoid water, oil, potholes and very rough

surfaces.

Assembly

The product is supplied folded for transport.

Proceed as follows to set it up for use:

Unfolding (Fig. A)

1. Release the lower quick-release connector (1).

2. Pull the lever (2) upward and fold the steering

post (3) forward until it locks into place.

3. Secure the folding mechanism by locking the

lower quick-release connector.

Handle assembly (Fig. B)

1. Remove the handles (4) from the holders (5).

2. Push in the locking buttons (6) on the handles

and slide the handles into both sides of the

T-tube (7) on the steering post. You must hear

the locking buttons lock into the designated

holes (8).

Adjusting the steering post (Fig. C)

The steering post can be adjusted to four differ-

ent levels. Only use the product with the locking

button locked into one of the four designated

holes and after securing the steering post with

the quick-release connector!

1. Release the quick-release connector (9) on the

steering post.

2. Pull up on the steering post (10) until the

locking button (11) latches into one of the four

holes (12).

3. Secure the steering post by locking the quick-

release connector.

Steering head bearing (Fig. D)

On product delivery the steering head bearing

is preset. If the handlebar has too much play

after some time or becomes too tight, have the

steering head bearing adjusted by a speciality

retailer or a bicycle shop.

Readying the product

fortransport

1. Release the quick-release connector on the

steering post, push in the locking button, push

the steering post all the way in, then tighten

the quick-release connector.

2. Push the locking buttons on the handles, pull

the handles out of the T-tube, and secure in

the holders.

3. Release the lower quick-release connector

(Fig. E) and pull the lever (2) up, push the

steering post toward the deck until it locks into

place (Fig. F). Tighten the lower quick-release

connector (Fig. G).

Use

Riding, braking, parking (Fig. H)

• Place one leg on the deck (13) and put

into motion by evenly pushing off with the

otherleg.

• Step on the fender (14) to brake.

• Swing out the stand (15) to park.

Only park the scooter on level surfaces.

Maintenance

Replacing the rollers (Fig. I)

Important!

Please refer to chapter “Technical

Data”. Rollers with a different diam-

eter can alter the riding properties

and possibly endanger the user. Do

not use rollers which cannot be easily

installed. Never install rollers larger

than the original rollers on the scooter.

Rollers wear down. This wear depends on many

factors, such as the ground, size and weight of

the user, weather conditions, and the material

and hardness of the rollers. They therefore oc-

casionally need to be replaced.

1. Loosen the axle bolts (16) using two size 5

socket head wrenches.

2. Remove the axle bolts and remove the roller.

3. Install the new roller (17) and secure with the

axle bolts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crivit BS-2418 IAN 277828 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info