Bedienungsanleitung Crivit BW 4533 IAN 292827 (Seite 9 von 30) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

736507

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

11GB/IE

Prevent property damage!

• Avoid water, oil, potholes and very rough

surfaces.

Assembly

The product is supplied folded for transport.

Proceed as follows to set it up for use:

Unfolding (Fig. A)

1. Pull the clamping lever (2) up and hold in

place.

2. Pull the lever (1) up, then release the clamping

lever (2) and unfold the steering post (3) until

it locks into place.

Handle assembly (Fig. B)

1. Remove the handles (4) from the holders (5).

2. Lift the cover flap (6).

3. Push in the locking buttons (7) on the handles

and slide the handles into both ends of the

T-bar (8) on the steering post. You must hear

the locking buttons lock into the designated

holes (9).

4. Push the cover flap over the locking buttons.

Adjusting the steering post (Fig. C)

The steering post can be adjusted to four differ-

ent levels. Only use the product with the locking

button locked into one of the four designated

holes and after securing the steering post with

the quick-release connector!

1. Release the quick-release connector (10) on

the steering post.

2. Pull up on the steering post (11) until the

locking button (12) latches into one of the four

holes (13).

3. Secure the steering post by locking the

quick-release connector.

Note: If the quick release is not tight against the

bar when closed, tighten the knurled screw using

the included socket head wrench.

Verify the quick release is locked before tight-

ening.

Steering head bearing (Fig. D)

On product delivery the steering head bearing

is preset. If the handlebar has too much play

after some time or becomes too tight, have the

steering head bearing adjusted by a speciality

retailer or a bicycle shop.

Brake

Adjusting the brake

ATTENTION!

The brake must be adjusted so the

back wheel moves freely when the

brake lever is released and locks when

engaging the brake lever.

Turn the adjusting and locking nut (21) to the left

to reduce the braking force, turn the adjusting

and locking nut to the right to increase the brak-

ing force (Fig. E).

Readying the product

fortransport

1. Release the quick-release lever (10) on

thesteering post and push in the locking

button (12) (Fig. C).

2. Push the steering post (11) in all the way and

tighten the quick-release lever (10) (Fig. C).

3. Lift the cover flap (6) (Fig. B).

4. Push in the locking buttons (7) on the handles

and pull the handles (4) out of the T-bar (8)

(Fig. B).

5. Secure the handles in the holders (5) (Fig. B).

6. Pull the clamping lever (2) up and hold

in place (Fig. F). Pull the lever (1) up, then

release the clamping lever (2).

7. Move the steering post toward the deck until it

locks into place (Fig. F).

Use

Riding, braking, parking (Fig. G)

• Place one leg on the deck (14) and put into

motion by evenly pushing off with the oth-

erleg.

• To brake, step on the brake plate (15) or pull

the brake lever (Fig. E).

• Swing out the stand (16) to park.

Only park the scooter on level surfaces.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crivit BW 4533 IAN 292827 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info