Bedienungsanleitung Crivit ID-1814 IAN 273711 (Seite 5 von 18) (Französisch)

736846

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

7GB/IE

Avoid damage to property!

• Do not erect the tent so that the tent entrance

is in the direction of the wind. Wind could

damage the tent.

• All the tent materials suﬀer material fatigue

and bleaching if they are exposed to

prolonged, strong sunlight. For this reason,

when the tent is to be used over longer

periods, erect it in a shady position.

Do not leave the tent assembled

unnecessarily.

Assembly

NOTE!

Perform a test assembly before the camping trip.

In doing so, ensure that all the accessories are

present.

Selecting a location for

placing the tent

Choose a place that is as ﬂat and clean as

possible. Avoid dips in the ground.

Remove stones, branches and other sharp ob-

jects in order to prevent damage to the tent ﬂoor.

Use natural shade, such as hedges, rocks, etc.

Use the appropriate pegs for sandy ground in

order to prevent accidental loosening of the

tension.

NOTE!

Insert the pegs into the ground at a slight angle

to achieve good strength but without causing

tension in the tent surface. The tent material and

tension points should only be slightly taut, so that

it can compensate for pressure from the wind.

Ensure that there is not too much pressure on the

tent. Check the tent tension according to weather

condition.

NOTE!

Water condensation occurs basically in every

tent, however particularly during strong ﬂuctu-

ations in temperature. After a night in the tent,

there will be drops of condensation on the inner

wall. Condensation is not evidence of leakiness.

Good ventilation reduces condensation in the

tent.

1. Spread the base of the inner tent ﬂat on the

ground, close the zips for the entrance and ﬁx

the loops at all four corners with the pegs

(Fig. B).

2. Build together the segments of the tent poles

(3) and (4). Slide the two black tent poles (3)

diagonally through the loops in the middle of

the inner tent (Fig. C). Secure the inner tent on

the tent poles using the clips (Fig. D).

3. Turn the tent around and insert the metal pins

at the corners of the inner tent into the end

of the tent poles so that these are under

tension (Fig. E).

4. The storage net (9) can now be hooked onto

the roof ridge in the interior of the inner tent

(Fig. F).

5. Place the outer tent over the inner tent

(Fig. G). Secure the outer tent using the bands

to the tent poles and at the crossing point in

the frame. Push the grey tent poles (4) through

the frame tunnel in the outer tent (Fig. H).

Right the frame up and insert the metal pins

from the corners of the inner tent into the end

of the tent poles. Secure the outer tent with

10 pegs and ensure that the loops at the four

corners are ﬁxed with the pegs of the inner

tent (Fig. I).

6. Secure each of the 6 guy ropes with a peg.

The length of the guy ropes can be adjusted

with the tensioner (Fig. J).

Disassembly

NOTE!

Disassemble the tent, if possible, when clean

and dry to prevent the formation of mould and

mildew. After disassembling in rain, immedia-

tely dry the tent. Clean all the parts thoroughly

before packing them away.

• Remove the pegs and guy ropes.

• Remove the tent poles, fold them together

and disassemble the inner and outer tents.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crivit ID-1814 IAN 273711 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Crivit ID-1814 IAN 273711

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info