Bedienungsanleitung Crivit Inshore 335 V IAN 282780 (Seite 14 von 54) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

736874

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Monitoring the operating pressure

IMPORTANT!

The PVC material will stretch a little

following initial inﬂation and will never

return to its original size.

Please remember that this data can

vary slightly, depending on the cargo it

is carrying and the outside

temperature.

Pump up the air chambers

/ / so that they

feel ﬁrm to the touch and no wrinkles can be

seen in the material. Press on each air chamber

with your thumb; you should just about be able

to press the material in slightly.

Measuring strips and monitoring

ruler (Fig. H, I)

To monitor the air chamber / operating

pressure, place the  0 of the monitoring ruler

(Fig. I) over the 0 of the measuring strip

(Fig. H) on the article.

During initial inﬂation, the maximum stretch point

MUST NOT exceed Position A on the monitoring

ruler.

From the second use onwards, pump up the craft

so that the 10 on the measuring strip is between

Position A and Position 10 of the monitoring

ruler.

Inﬂating the air chambers

Floor chamber with stopper

valve

/ Lower side chamber with stopper

valve (Fig. J)

1. Open the valve closure

2. Pump up each air chamber.

3. Close the valve closure and press the sealed

valve down using a little pressure.

/ Upper side chamber with screw

valve (Fig. F)

1. Inﬂate the upper side chambers / and

seal the closure cap by screwing in a

clockwise direction.

Front seat, Rear splash guard

with seat, Prow splash guard,

Triangular cushion (Fig. K - N)

Note:

The ropes must be tied using a reef

knot and a ﬁgure-of-eight hitch knot

(Fig. K, L)

1. Front seat (Fig. M, N)

Pump up all of the air chambers. Place the seat

underneath both of the upper side air chambers

/ , so that the seat is securely ﬁtted. Tie the

seat using the 80cm rope through the eyelet on

the ﬂoor chamber (Fig. M) as well as with

a 150cm rope in a zig-zag shape through the

eyelets on the side chambers and (Fig. N).

2. Rear splash guard with seat

Pump up all of the air chambers. Press the seat

underneath both of the upper side air chambers

/ , so that the seat is securely ﬁtted.

Fasten the rear splash guard with seat with a

280cm rope in a zig-zag shape through the

eyelets on the side chambers and .

3. Prow splash guard

Pump up all of the air chambers and fasten the

prow splash guard with a 280cm rope in a zig-

zag shape to the eyelets on the side chambers

and .

4. Triangular cushion

Position the inﬂated triangle cushion securely in

the bows of the kayak, where it serves as a foot

support for the person sitting at the front.

Dismantling the kayak

Remove the front seat, the rear splash guard with

seat, the prow splash guard and the triangular

cushion.

Deﬂating

Deﬂate the kayak as follows:

1. To deﬂate the ﬂoor chamber

, the lower side

chambers / , the front seat , the rear

splash guard with seat , and the prow

splash guard , pull the stopper valve out

of its concealed location and press the shaft

lightly or use the deﬂation tube .

GB/IE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crivit Inshore 335 V IAN 282780 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info