Bedienungsanleitung Croozer Kid Plus 2014 (Seite 26 von 104) (Englisch)

772404

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

26 CroozerKid14-ENG-USACAN-11-13

Converting the Croozer Kid Plus to a Jogger

6. Insert the security pin (1) through both holes of the

hitch-arm attachment bracket.

7. Lock the security pin in place by snapping the wire

loop over the end of the pin (see Fig. 44). Then pull

gently on the security pin to ensure that the wire loop

is locked securely onto the end of the pin.

8. Repeat steps 3 to 7 for the right wheel arm.

Always check that the wire loops of the security pins are

snapped securely onto the pin ends. If the security pins

are not securely locked, the wheel arms could fall off

while in use, resulting in accidents with serious injury or

death.

Installing the Jogger wheel

1. Open the quick-release of the Jogger wheel by lifting

the quick-release lever (3) until the lever side marked

“OPEN” is facing outwards, away from the wheel.

2. Slide the Jogger wheel (4) as far as possible into the

slots in the dropouts of the wheel arms. The  attened

surfaces (5) on the axle must be lined up with the slots

in the dropouts.

Tip: If you have difficulties sliding the Jogger wheel into

the slots in the dropouts, then loosen the tension-

adjusting nut of the quick-release by turning it a few

turns counterclockwise and try again.

3. With the quick-release lever (3) in the open position,

tighten the tension-adjusting nut (6) by turning it clock-

wise until you feel a slight resistance.

4. Close the quick-release by moving the lever (3)

towards the wheel arm until the lever side marked

“CLOSE” is facing outwards. If the tension-adjusting

nut has been tightened the proper amount, you will

be able to feel the resistance increase when the lever

is about halfway closed, i.e. parallel to the axle. The

adjustment is correct if you can fully close the lever

but with considerable force. In the closed position, the

lever should be parallel to the dropout (5) of the wheel

arm, i.e. it should not stick out to the side.

5. Check whether the quick-release is securely engaged

by trying to rotate the endcap of the mechanism

(where the lever is attached) without opening the lever.

If the endcap is loose enough to rotate, then the

clamping force is inadequate. In this case, open the

lever, and tighten the tension-adjusting nut (4) half a

turn clockwise. Repeat steps 4 and 5.

If it is impossible to push the quick-release lever (6)

into the closed position, then open the lever, and

unscrew the tension-adjusting nut half a turn counter-

clockwise. Repeat steps 4 and 5.

6. Hold the Jogger wheel with both hands, and try to

rock it back and forth to check that the quick-release

mechanism is securely fastened. If there is any play in

the wheel, repeat steps 4 and 5.

ClosedOpen

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Croozer Kid Plus 2014 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Croozer Kid Plus 2014

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info