Bedienungsanleitung Croozer Kid Plus 2019 (Seite 24 von 52) (Englisch)

772389

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

22 CroozerKidPlus-Kid19-ENG-1-19

Converting the Croozer to a Jogger

If the hitch arm or Stroller wheel has been installed, re-

move these components.

Attaching the wheel arms

The Jogger Kit consists of two wheel arms, a Jogger wheel

and a safety wrist strap. The handlebar should already be

mounted. The two wheel arms are attached to the frame in

the same way as the hitch arm. One wheel arm is mounted to

the hitch-arm attachment bracket on the left side of the frame,

and the other, to the wheel-arm attachment bracket on the

right side of the frame (relative to the direction of travel).

Tip: The first time you install the Jogger Kit, we recom-

mend tipping the Croozer onto its back end (resting

on the handlebar) in order to have a better view of the

parts while familiarising yourself with the procedure.

Make sure that your working surface is clean and

smooth to avoid soiling and/or damaging the fabric

body. Later, once you are familiar with the installation

and removal procedures, you can install the Jogger

Kit with the front of the Croozer slightly raised.

1. Lift the front of the Croozer, or tip the frame onto its

back end.

2. Pull out the security pin (1). Follow the same steps for

removing the security pin in the wheel-arm attachment

bracket on the other side of the frame.

Tip: Before you start, it is helpful to lay the two wheel arms

on the ground in the position they will be mounted:

each arm should curve inwards, and the holes (4) in

the wheel arms should be facing upwards.

3. Hold the left wheel arm (2) at an approx. 45° angle to

the hitch-arm attachment bracket.

4. Guide the retaining bolts (3) of the left wheel arm gen-

tly into the slots of the hitch-arm attachment bracket.

5. Then fold the wheel arm upwards into the hitch-arm

attachment bracket until the retaining bolts (3) of the

wheel arm are fully engaged in the slots of the attach-

ment bracket.

6. Press the wheel arm rmly against the hitch-arm at-

tachment bracket.

Do not let the strap of the security pin get caught be-

tween the hitch arm and attachment bracket as this could

damage the strap.

7. Insert the security pin (1) as far as it will go through

the upper hole of the hitch-arm attachment bracket.

The head of the security pin is magnetic and will ad-

here to the hitch-arm attachment bracket.

8. Repeat these steps to attach the right wheel arm.

Always check that the security pins have been inserted

as far as they will go and that the heads are held firmly

against the attachment brackets by magnetic force. Oth-

erwise, the wheel arms could fall off while in use, result-

ing in accidents with serious injury or death.

9. To remove the wheel arms, follow these instructions in

the reverse order.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Croozer Kid Plus 2019 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Croozer Kid Plus 2019

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info