Bedienungsanleitung Crunch GTR 250.4 (Seite 14 von 24) (Deutsch, Englisch)

63811

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

FU SE

BRIDGED

SPEAKER OUTPUT

GND REM 12V

POWER INPUT

L R

e13

021257

FUSE

Fuse

Battery

Remote

Chassis

Ground

General Installation Notes

The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such as beneath a seat. Please be sure to

locate this unit where you have reasonable air circulation and protection from moisture. When considering the mounting location you should

minimize the length of the power and speaker leads. Minimizing both leads will yield a more reliable installation. It is also important to ensure that

the heat sink fins are not against a panel or a surface, preventing air circulation. Do not install the amplifier on a subwoofer box or on vibrating

parts of the vehicle, since the vibrations can cause damage to the amplifiers electrical components.

Installation of the amplifier

Mark the location for the mounting screw holes by using the amplifier as a

template. Drill holes at the marked locations and firmly fasten the amplifier

in place with the mounting screws supplied in the accessory kit. Before drilling

or cutting any holes, investigate the layout of your automobile thoroughly:

Take care when working near the gas lines or hydraulic lines and

electrical wiring od your car.

Electrical Connection

Ground (GND)

This wire is the electrical ground and must be fastened securely to the vehicle chassis.

The best method is to use a threading sheet metal screw since the threads cut into

bare metal. Ensure that all paint or other insulation is remove from around the hole area,

and using self tapping screw, securely affix the bare wire ends to the vehicle chassis. Use

as short a piece of cableas possible - use the same gauge as was used for the +12V cable.

Make sure that the connection is safe, a loose connection may result in amplifier noise and fault condition.

Remote (REM)

Many music sources have an output terminal for connection of the remote turn-on of the power amplifier. If a radio doesn't have a remote turn-on

feature, then you can use the antenna relay wire, which activates the antenna motor. Please note, if the power antenna retracts when the radio is

operating, then you cannot use the antenna relay wire to operate the remote turn-on.

Battery Connection (+12V)

This wire is usually connected directly to the positive battery terminal. Ensure that the + power supply wire is fused via an assigned fuse in line

with the + power supply wire. Please use a sufficient gauge for the installed amplifiers (min 16-25 mm). This connection must be completed using

spade lug with insulating sleeve.

Fuses

The integrated amplifier fuses protect the units from short circuit and overload. The fuse rating is for 4 Ohm loads (impedance)

of the speakers, for 1 or 2 Ohm loads the fuses may have to get increased in case of higher power consumption.

Power / Ground / Remote Connection

Installation & Electrical Connection

GTR250.2 - GTR550.2 - GTR250.4 - GTR350.4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crunch GTR 250.4 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info