Bedienungsanleitung Crunch gtx 2600 (Seite 23 von 32) (Deutsch, Englisch)

168673

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

GTX2400 - GTX2600

Do not connect loudspeaker cables with the vehicle chassis.

Always ensure the correct polarity of all connections.

REFERENCE NOTE

INTERCONNECTION EXAMPLE 1-Channel Mode: 1x Mono Subwoofer bridged

Use the bass enhancement with care.

A high bass boost may cause damage to your speakers and hearing abilities.

INTERCONNECTION

• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.

If your headunit is equipped with a additional subwoofer lineout (SUB OUT), it is recommended to use this lineout.

• Connect the subwoofer with the speaker outputs (SPEAKER OUTPUT + BRIDGED -) by using appropriate wires.

• Ensure by any means, that the total impedance load of the channel-pair is not lower than 4 ohms. Too low impedance cause high

temperature and will shut down the amplifier operation.

• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could

damage the speakers.

CROSSOVER SETTINGS

• In the mono/subwoofer mode the X-OVER switch must set to the LP/BP position (Lowpass/Bandpass mode), thereby the higher

frequencies will be eliminated. The cut-off frequency ist adjustable with the LOW PASS controller and should be set between

60 to 100 Hz, depending on the size of the subwoofer.

• In the lowpass mode (LP/BP) the HIGH PASS controller works also as subsonicfilter, that eliminates the ultra-low, not hearable and

harmful frequencies to generate a bandpass signal (Bandpass mode). The subsonic frequency should be set between 15 to 40 Hz,

depending on the size of the subwoofer. NOTE: If this value is higher than the lowpass setting, no sound is hearable.

LEVEL CONTROLLER

• Turn the LEVEL INPUT controller of the amplifier to the 4V position.

• Turn the volume controller of the headunit to 80 - 90% of its full setting.

• Turn the LEVEL INPUT controller clockwise until you hear some distortion.

• Then turn back the LEVEL INPUT controller slightly until you hear a cleaner sound.

BASS BOOST CONTROLLER

• The BASS BOOST controller adjusts the bass enhancement between 0db and +12dB.

• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.

Use this controller carefully!

BASS REMOTE

• The enclosed BASS REMOTE Controller adjusts the bass-level e.g. from the driver’s seat.

Please use only this enclosed bass remote controller and cable.

Connect stereo RCA output

(L/R or SUB OUT)

of the headunit with

LINE INPUT L/R of the amplifier

R L

Subwoofer

4 – 8 Ohms

Switch position LP/BP

Connect the bass remote

controller and the

remote terminal on the amplifier

with the enclosed cable.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crunch gtx 2600 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info