Bedienungsanleitung Crunch MXB 1000 (Seite 11 von 16) (Deutsch, Englisch)

66425

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

GND REM 12V

POWER INPUT

FUSE

Electrical Connections

Ground (GND)

This wire is the electrical ground and must be fastened securely to the vehicle's chassis. The best method is to use a threading sheet

metal screw since the threads cut into bare metal. Ensure that all paint or other insulation is removed from around the hole area, and

using self tapping screw, securely affix the bare wire ends to the vehicle chassis. Use as short a piece of cable as possible - use the

same gauge as was used for the +12V cable. Make sure that the connection is safe, a loose connection may result in amplifier noise

and fault condition.

Remote (REM)

Many radios or other music sources have an output terminal for connection of the remote turn-on of the power amplifier. If a radio

doesn't have a remote turn-on feature, then you can use the antenna relay wire, which activates the antenna motor. Please note, if the

power antenna retracts when the radio is operating, then you cannot use the antenna relay wire to operate the remote turn-on.

Battery Connection (+12V)

This wire is usually connected directly to the positive battery terminal. Ensure that the + power supply wire is fused via an assigned fuse

in line with the + power supply wire. Please use a sufficient gauge for the installed amplifiers (16-25 mm ).As additional fuse a external

in-line fuse (not enclosed) with max. 60A in the +12V cable is suggested. This Fuse must be installed close-by the vehicle’s battery.

Fuses

The integrated amplifier fuses protect the units from short circuit and overload.

Replace a defective fuse only with a fuse of the same design and rating.

General Installation Notes

The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such as

beneath a seat. Please be sure to locate this unit where you have reasonable air circulation

and protection from moisture. When considering the mounting location you should minimize

the length of the power and speaker leads. Minimizing both leads will yield a more reliable

installation. It is also important to ensure that the heat sink fins are not against a panel or a

surface, preventing air circulation. Do not install the amplifier on a subwoofer box or on vibrating

parts of the vehicle, the vibrations can cause damage to the amplifier. Do not install the amplfier

on the hattrack of your vehicle, otherwise the surface get discolored by the solar exposure.

Amplifier Installation

Mark the location for the mounting screw holes by using the amplifier as a template. Drill

holes at the marked locations and firmly fasten the amplifier in place with the mounting

screws supplied in the accessory kit.

Before drilling or cutting any holes, investigate the layout of your automobile thoroughly:

Take care when working near the gas lines or hydraulic lines and electrical wiring.

CHASSIS

GROUND

CHASSIS

GROUND

REMOTE

BATTERY

FUSES

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crunch MXB 1000 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info