Bedienungsanleitung Crunch MXB 5900i (Seite 12 von 20) (Deutsch, Englisch)

498273

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

General Installation Notes

The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such as beneath a seat.

Please be sure to locate this unit where you have reasonable air circulation and protection from moisture. When considering the

mounting location you should minimize the length of the power and speaker leads. Minimizing both leads will yield a more reliable

installation. It is also important to ensure that the heat sink fins are not against a panel or a surface, preventing air circulation.

Do not install the amplifier on a subwoofer box or on vibrating parts of the vehicle, since the vibrations can cause damage to

the amplifiers electrical components.

Installation of the amplifier

Mark the location for the mounting screw holes by using

the amplifier as a template. Drill holes at the marked

locations and firmly fasten the amplifier in place with

the mounting screws supplied in the accessory kit.

Before drilling or cutting any holes, investigate the

layout of your automobile thoroughly:

Take care when working near the gas lines or

hydraulic lines and electrical wiring.

Electrical Connection

Ground (GND)

This wire is the electrical ground and must be fastened securely to the vehicle chassis. The best method is to use a threading

sheet metal screw since the threads cut into bare metal. Ensure that all paint or other insulation is remove from around the

hole area, and using self tapping screw, securely affix the bare wire ends to the vehicle chassis. Use as short a piece of cable

as possible - use the same gauge as was used for the +12V cable. Make sure that the connection is safe, a loose connection

may result in amplifier noise and fault condition.

Remote (REM)

Many radios or other music sources have an output terminal for connection of the remote turn-on of the power amplifier. If a radio

doesn't have a remote turn-on feature, then you can use the antenna relay wire, which activates the antenna motor. Please note,

if the power antenna retracts when the radio is operating, then you cannot use the antenna relay wire to operate the remote turn-

on.

Battery Connection (+12V)

This wire is usually connected directly to the positive battery terminal. Ensure that the + power supply wire is fused via an

assigned fuse in line with the + power supply wire. Please use a sufficient gauge for the installed amplifiers. This connection

must be completed using spade lug with insulating sleeve.

Fuses

The integrated amplifier fuses protect the units from short circuit and overload. The fuse rating is for 4 Ohm loads (impedance)

of the speakers, for 2 Ohm loads the fuses may have to get increased by up to 50% in case of higher power consumption.

Power / Ground / Remote Connection

BRIDGED

SPEAKERS

+ L - + R -

GND REM BATT12V FUSE

REMOTE

(REM)

Chassis

Ground

Battery

12 Volt

Fuse

Chassis

Ground

HEAD UNIT

FUSE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crunch MXB 5900i Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info