Bedienungsanleitung Cube Road bike (Seite 60 von 75) (Deutsch)

657564

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

| 39 38 |

MTB/ ROAD BIKE/ TREKKINGMTB/ ROAD BIKE/ TREKKING

•

Move the saddle to the desired position.

•

For seat clamps with only one xing screw:

always tighten the seat clamp with the

correct, prescribed torque. Make sure that

all loosened parts join together with the

correct alignment (see Chapter 3.3.).

•

For seat clamps with two xing screws:

tighten one screw just for a quarter or a half

turn then continue with the other screw

in the same way. Do this as long as you´ve

reached the right torque (see Chapter 3.3.).

•

Please observe the specied tightening

torques in table 3.3.

8.3 Adjust saddle height

Risk of Personal Injury and Material

Damage!

A saddle set too high for children who

are not yet able to cycle safely without

assistance, could result in dangerous

driving conditions, falls, accidents, and/or

property damage.

•

Adjust the seat height in such a way that the

child's feet can touch the ground when in a

sitting position.

•

On a gripper clamp with bolt, you need a

hexagonal socket and a torque wrench of

the correct size. For a quick-release clamp,

please see Chapter 7.8.

1. Loosen the clamp as described in

Chapter 11.2.

2. Move the saddle and saddle stem to the

desired position. Please note the inst-

ructions regarding saddle stem insertion

distance in Chapter 11.2.

3. Clamp the saddle stem as described in

Chapter 11.2.

8.4 Adjust suspension forks

1. Please read the instructions for adjusting

your suspension forks in the suspension

fork manufacturer‘s parts instructions.

2. If your forks have a xed adjustment

mechanism as shown in the illustration,

please read the related instructions in

the suspension fork manufacturer‘s parts

instructions.

Suspension forks with elastomers and/

or steel springs are only suitable for one

overall weight range (= weight of rider

+ any baggage). This weight range is

usually within 20 kg.

Only the forks pre-tensioning can be

adjusted by compressing the springs by

means of an adjuster screw. This merely

changes the initial breakaway torque of

the forks.

That is, with greater pre-tensioning, the

forks only deect at higher operating

forces.

If the forks are pre-tensioned too much,

suspension travel is accordingly less.

The weight range for which the suspen-

sion elements in your forks are suited

can be found in the fork manufacturer‘s

instructions and/or you can consult your

dealer.

If your total weight is outside this range,

have your dealer t suspension elements

matching your weight.

8 Adjusting and servicing

your bike

You can modify your bike yourself.

Only make these adjustments yourself if

you have the appropriate technical know-

ledge and experience and the right tools

for the job.

8.1 Adjusting the adjustable stem

(optional)

•

Many bikes are tted with an adjustable

stem, the height and angle of which can be

adjusted. Only have the adjustment made in

a specialist workshop!

8.2 Adjust saddle position

Your saddle will be secured with one or two

clamping bolts.

To adjust it, you need a hexagonal socket of

the right size and a torque wrench.

1. To adjust the horizontal position or incli-

nation of your saddle:

•

Loosen the clamping bolt(s) a few turns until

the saddle can be turned easily and/or the

inclination angle adjusted.

Risk of Personal Injury and Material

Damage!

•

Damaged bicycle parts can have sharp edges

and injure you.

•

Check all the bike parts that you may come into

contact with while riding your bike.

•

Have damaged parts repaired or replaced

immediately by an authorised repair shop.

•

As for side stands with adjustable lengths:

check if the extendable part can be moved

by exerting hand force.

2. Check the secure stand of your bicycle.

•

Lean or place your bicycle on the unfolded

side stand.

•

Your bicycle must stand by itself.

•

When pushed slightly in any direction, your

bicycle must remain standing and not fall

over.

Risk of Personal Injury and Material

Damage!

Accessories that have not been tted

correctly or that have become loose can

jeopardise your safety when riding.

•

Check any accessory that is explicitly listed

herein to ensure that it has been secured

properly.

•

Immediately contact a specialist workshop

in case one of the following requirements is

not met.

3. Check any accessories that have been

retrotted.

•

Visually inspect the screw connections.

•

Try to twist or move the accessories out of

position by exerting hand force .

•

Tilt the whole bicycle against the direction

of travel and move it back and forth a few

times.

•

Lift your bicycle up (one or two centimetres)

and put it down again.

•

The accessories must not be loose, move or

twist.

•

No part of the accessories should touch the

wheels.

•

If tted, a bicycle stand should not be

unfolded.

•

There should be no noticeable noise.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cube Road bike Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cube Road bike

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info