Bedienungsanleitung Cubify Cube (Seite 30 von 31) (Englisch)

534701

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

Your Print Pad may become un-leveled when transporting your Cube. If this occurs, please follow these instructions to

level your Print Pad for optimum creation experience. The Print Pad pad can be leveled with the two adjusting bolts located

underneath the front and back of the pad.

1. Press the power button on the Cube control panel.

2. Ensure Print Pad is properly installed on print plate.

3. Finger tap SETUP on the touchscreen and scroll through the menu until LEVEL

PLATE appears. Press LEVEL PLATE; the Print Pad will move up to Print Jet tip.

4. Using the Up arrow, raise the Print Pad to the Print Jet tip until the tip is near the

Print Pad but not touching it.

5. Touch the “clockwise” and “counter-clockwise” buttons to automatically move the

Print Jet around the four corners of the Print Pad. During each movement along the

sides of the Print Pad, observe any gaps between the pad and the Print Jet. If there

are gaps on one side of Print Pad and the Print Jet tip is barely touching the Print

Pad on the other side, the Print Pad pad is not level.

NOTE: Please refer to the FRONT TO BACK or SIDE TO SIDE instructions on how

to turn the adjusting knob bolts to level the pad properly.

6. Place a standard sheet of paper between the Print Jet tip and the Print Pad where

the adjustment needs to be made. If the paper cannot slide between the Print Jet tip

and Print Pad, tap the down arrow key on touchscreen.

ROLL SIDE TO SIDE

If the gap between the Print Pad and Print Jet tip is at the right or left side, adjust the pad

using the rear adjusting knob bolt (B). If the gap is too low, the pad is too low and will

need to be moved up.

1. If the pad needs to be moved up, turn the front adjusting knob bolt (A) clockwise to

loosen and then turn the rear adjusting knob bolt (B) clockwise. To move the pad

down, turn the rear adjusting knob bolt (B) counterclockwise.

2. While adjusting, slide the paper between the Print Jet tip and Print Pad where the

adjustment was needed; the paper should slide back and forth with no resistance. If

resistance is felt, the pad is too high. Please repeat the adjustment.

3. Once adjustments are made, tighten the adjusting knob bolts.

TILT FRONT TO BACK

If the gap between the Print Pad and Print Jet tip is at the front or back of pad, adjust the pad using the rear adjusting knob

bolt (B). If the gap appears on the side, the pad is too low and will need to be moved up.

1. If the pad needs to be moved up, turn the front adjusting knob bolt (A) clockwise to loosen and then turn the back

adjusting knob bolt (B) clockwise. To move the pad down, turn the rear adjusting knob bolt (B) counterclockwise.

2. While adjusting, slide the paper between the Print Jet tip and Print Pad where the adjustment was needed; the paper

should slide back and forth with no resistance. If resistance is felt, the pad is too high. Please repeat the adjustment.

3. Once adjustments are made, tighten the adjusting knob bolts.

NOTE: After the print jet is adjusted, you will need to reset the print jet gap; please refer to Section 16: Setting Print

Jet Gap.

A B

24 PRINT PAD LEVELING INSTRUCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cubify Cube Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info