Bedienungsanleitung Cupra Ateca 2018 (Seite 318 von 372) (Englisch)

817302

318

Zoom out

Zoom in

Vorherige Seite

1/372

Nächste Seite

Practical tips

The oil change intervals are shown in the

Maintenance Programme.

WARNING

Only change the engine oil yourself if you

have the specialist knowledge required!

●Before opening the bonnet, read and ob-

serve the warnings ››› page 310.

●Wait for the engine to cool down. Hot oil

may cause burn injuries.

●Wear eye protection to avoid injuries,

such as acid burns, caused by splashes of

oil.

●When removing the oil drain plug with

your fingers, keep your arm horizontal to

help prevent oil from running down your

arm.

●Wash your skin thoroughly if it comes into

contact with engine oil.

●Engine oil is poisonous! Used oil must be

stored in a safe place out of the reach of

children.

CAUTION

No additives should be used with engine oil.

This could result in engine damage. Any

damage caused by the use of such additives

would not be covered by the factory war-

ranty.

For the sake of the environment

●Because of disposal problems and the

special tools and specialist knowledge re-

quired, we recommend that you have the

engine oil and filter changed by a Technical

Service.

●Never pour oil down drains or into the

ground.

●Use a suitable container when draining

the used oil. It must be large enough to

hold all the engine oil.

Cooling system

Topping up coolant

Read the additional information carefully

››› page 42

Top up coolant when the level is below the

MIN (minimum) mark.

Checking coolant level

–Park the vehicle in a horizontal position.

–Switch the ignition off.

–Read off the coolant level on coolant ex-

pansion tank. When the engine is cold, the

coolant level should be between the

marks. When the engine is hot, it may be

slightly above the upper mark.

Topping up coolant

–Wait for the engine to cool down.

–Cover the coolant expansion tank cap with

a cloth and carefully unscrew it to the left

››› .

–Top up the coolant only if there is still cool-

ant in the expansion tank, otherwise you

could damage the engine. If there is no

coolant in the expansion tank, do not con-

tinue driving. You should obtain professio-

nal assistance ››› .

–If there is still some coolant in the expan-

sion tank, top up to the upper mark.

–Top up with coolant until the level be-

comes stable.

–Screw the cap back on correctly.

Any loss of coolant fluid normally indicates a

leak in the cooling system. Take the vehicle

straight to a specialised workshop to have

the cooling system examined. If there are no

leaks in the engine cooling system, a loss of

coolant can only occur if the coolant boils

and is forced out of the system as a result of

overheating.

WARNING

●The cooling system is under pressure. Do

not unscrew the cap on the coolant expan-

sion tank when the engine is hot: risk of

burns!

316

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Ateca 2018 Seite 318

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Ateca 2018

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info