Bedienungsanleitung Cupra Ateca 2018 (Seite 322 von 372) (Englisch)

817302

322

Zoom out

Zoom in

Vorherige Seite

1/372

Nächste Seite

Practical tips

–2. When the repair is finished, recon-

nect the negative pole of the battery.

●Switch off all electrical devices before re-

connecting the battery. Reconnect first the

positive cable and then the negative cable.

Never reverse the polarity of the connec-

tions. This could cause an electrical fire.

●Ensure that the vent hose is always con-

nected to the battery.

●Never use damaged batteries. This could

cause an explosion! Replace a damaged

battery immediately.

CAUTION

●Never disconnect the battery if the igni-

tion is switched on or if the engine is run-

ning. This could damage the electrical sys-

tem or electronic components.

Charging the battery

Terminals for charging the battery are fitted

in the engine compartment.

–Note the warnings ››› in Important

safety warnings for handling a vehicle

battery on page 319 and ››› .

–Switch off all electrical devices. Remove

the ignition key.

–Raise the bonnet ››› page 17.

–Open the battery cover.

–Connect the charger clamps as described

to the positive pole of the battery (+) and

exclusively to an earth on the bodywork

(–).

–Only use a charger which is compatible for

use with 12 V nominal voltage batteries.

The charge must not exceed a voltage of

15 V.

–Now connect the battery charger to the

power socket and switch on.

–At the end of the charging process: switch

off the battery charger and disconnect the

power socket cable.

–Finally disconnect the charger cables from

the battery.

–Replace the battery cover correctly.

–Close the bonnet ››› page 17.

Important: Before you charge the battery

make sure you read the manufacturer's in-

structions for using the battery charger.

WARNING

Never charge a battery that has frozen: re-

place it! Failure to do so may lead to an ex-

plosion.

Note

Use only the terminals in the engine com-

partment to charge the battery.

Replacing the battery

The new battery should have the same spec-

ifications (amperage, load and voltage) as

the used battery.

Your vehicle is equipped with an intelligent

power management system to control the

distribution of electrical energy ››› page 234.

The power management function ensures

that the battery is charged much more effi-

ciently than on vehicles without a power

management system. To maintain this func-

tion after replacing the battery, we recom-

mend that the replacement battery used is

of the same make and type as the original fit-

ted battery. To make proper use of the power

management function after the battery has

been changed, have the battery coded to

the power management mode at a special-

ised workshop.

CAUTION

●Some vehicles, for example those with

the Start-Stop system* are fitted with a

special battery (AGM-type or EFB-type bat-

tery). If any other type of battery is fitted,

the Start-Stop function may be considera-

bly reduced and the vehicle may not stop

on repeated occasions.

●Make sure that the vent hose is always at-

tached to the original opening on the side

of the battery. Gases or battery acid can

320

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Ateca 2018 Seite 322

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Ateca 2018

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info