Bedienungsanleitung Cupra Ateca 2020 (Seite 311 von 352) (Englisch)

817296

311

Zoom out

Zoom in

Vorherige Seite

1/352

Nächste Seite

Wheels

●Tyre pressure is insufficient.

●The tyre structure is damaged.

●The vehicle is unbalanced because of a

load.

●The wheels on an axle are subject to a

heavier load (e.g. with a heavy load).

●The vehicle is fitted with snow chains.

●The temporary spare wheel is fitted.

●The wheel on one axle is changed.

There may be a delay in the reaction of the

tyre pressure monitoring indicator  or it

may not indicate anything under certain cir-

cumstances (e.g. sporty driving, snow-cov-

ered or unpaved roads, or when driving with

snow chains).

Calibrate the tyre pressure monitoring in-

dicator

After changing the tyre pressure or replacing

one or more wheels, the tyre pressure moni-

toring indicator must be recalibrated. Do the

same, for example, when the front and rear

wheels are swapped.

●Switch the ignition on.

●Save the new inflation pressure in the Info-

tainment system: function button  > SET-

TINGS > Tyres

››› page 88 .

When driving, the system self-calibrates the

tyre pressure provided by the driver and the

wheels fitted. After a long journey with varied

speeds the programmed values are collected

and monitored.

With the wheels under very heavy loads, the

tyre pressure must be increased to the total

recommended tyre pressure before calibra-

tion

››› Fig. 209.

WARNING

When the tyres are inflated at different

pressures or at a pressure that is too low

then a tyre may be damaged resulting in a

loss of control of the vehicle and a serious

or fatal accident.

●If the lamp  lights up, reduce speed im-

mediately and avoid any sudden turning or

braking manoeuvre. Stop when possible,

and check the tyre pressure and status.

●The tyre pressure monitoring system can

only operate correctly if all of the tyres are

inflated to the correct pressure when cold.

●If a tyre has not been punctured and it

does not have to be changed immediately,

drive to the nearest specialised workshop

at a moderate speed and have the tyre

checked and inflated to the correct pres-

sure.

Note

●Driving for the first time with new tyres at

a high speed can cause them to slightly ex-

pand, which could then produce an air

pressure warning.

●If excessively low tyre pressure is detec-

ted with the ignition on, an audible warning

will sound. In the event that there is a fault

in the system, an audible warning will

sound.

●Driving on dirt tracks for a long period of

time or driving in a sporty style can tempo-

rarily deactivate the TPMS. The control

lamp shows a fault, but disappears when

road conditions or the driving style change.

●Do not only rely on the tyre pressure

monitoring system. Regularly check your

tyres to ensure that the tyre pressure is cor-

rect and that the tyres are not damaged

due to puncture, cuts, tears and im-

pacts/dents. Remove objects from the

tyres only when they have not pierced the

tyres.

●The tyre pressure monitoring indicator

does not function when there is a fault in

the ESC or ABS

››› page 249 .

309

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Ateca 2020 Seite 311

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Ateca 2020

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info