Bedienungsanleitung Cupra Ateca 2023 (Seite 99 von 355) (Englisch)

817294

Zoom out

Zoom in

Vorherige Seite

1/355

Nächste Seite

Lights

Vehicle lighting

Switching on the main beam assist

●Turn on the ignition and turn the light switch

to position .

●From the base position, press the turn sig-

nal and main beam headlights lever forwards

›››Fig.80 3.

When the main beam assist is switched on,

the control lamp on the instrument cluster

screen turns on. When the main beam is on,

the blue main beam control lamp on the

instrument cluster switches on.

Switching the main beam assist o

●Turn the headlight switch to a position other

than .

●EITHER: if main beam assist is on, pull the

turn signal light and main beam headlights

lever back ›››Fig.80 4.

●OR: if the main beam assistant is on, but the

main beam does not turn on, press the turn

signal and main beam lever forwards to turn

the main beam on manually. Pull the turn sig-

nal and main beam lever back to switch o the

main beam manually, if necessary.

● OR: switch o the ignition.

System limitations

In the following cases, the main beam head-

light must be switched o manually because

the main beam assist will not disconnect it on

time or disconnect it at all:

●On roads with insuicient lighting with very

reective signs

●If road users are insuiciently lit up, e.g. pe-

destrians or cyclists.

●On closed curves, when the traic in the

opposite direction is partially hidden, on pro-

nounced slopes or inclinations.

●On roads with traic in the opposite direction

and with a central reservation barrier where

the driver can see over it e.g. lorry drivers.

●In the event of fog, snow or heavy rain

●In the event of dust or sand storms

●If the windscreen is damaged in the camera's

eld of vision.

●If the camera's eld of vision is misted up,

dirty or covered by a sticker, snow or ice.

●If the camera is damaged or if the power

supply has been cut o.

WARNING

The convenience features of the main beam

assist should not encourage the taking of

risks. The system is not a replacement for

driver concentration.

●You are always in control of the main beam

and adapting it to the light, visibility and traf-

c conditions.

●It is possible that the main beam headlight

control does not recognise all driving situa-

tions and is limited under certain circumstan-

ces.

●When the eld of vision of the camera is

dirty, covered or damaged, operation of the

main beam control may be aected. This also

applies when changes are made to the vehi-

cle lighting system, for example, if additional

headlights are installed.

NOTICE

To avoid aecting the operation of the sys-

tem, take the following points into considera-

tion:

●Clean the eld of vision of the camera reg-

ularly and make sure it is free of snow and ice.

●Do not cover the eld of vision of the cam-

era.

●Check that the windscreen is not damaged

in the area of the eld of vision of the cam-

era.

Note

●The headlight asher can be turned on and

o manually at any time with the turn signal

and main beam lever ›››page97.

●If there are objects that radiate light in the

camera's area of inuence, e.g. a portable

navigation system, this may aect the opera-

tion of the main beam assist system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Ateca 2023 Seite 99

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Ateca 2023

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info