Bedienungsanleitung Cupra Ateca 2023 (Seite 104 von 355) (Englisch)

817294

104

Zoom out

Zoom in

Vorherige Seite

1/355

Nächste Seite

104

Visibility

Rain sensor o.

Rain sensor on; automatic wipe if neces-

sary.

Setting sensitivity level of rain sensor:

– Set control to the right: high sensitivity.

– Set control to the left: low sensitivity.

When the ignition is switched o and then

back on, the rain sensor stays on and starts

operating again when the windscreen wipers

are in position ›››Fig.82 1 and the vehicle is

travelling at more than 16km/h (10mph).

Abnormal operation of the rain and light

sensor

The possible causes of anomalies and errone-

ous interpretations in the sensitive surface area

›››Fig.83 of the rain sensor are, among oth-

ers:

●Damaged wipers: a lm of water on the

damaged blades may lengthen the activation

time, reduce the washing intervals or result in a

fast and continuous wipe.

●Insects: the impact of insects may cause the

wiper to activate.

●Salt on the road: in winter, salt spread on

the roads may cause an excessively long wipe

when the windscreen is almost dry.

●Dirt: dry dust, wax, coating on glass (Lotus

eect) or traces of detergent (car wash) may

reduce the eectiveness of the rain sensor or

make it react more slowly, later or not at all.

Regularly clean the sensitive surface of the rain

sensor ›››Fig.83 (arrow) and check for possi-

ble damage to the wiper blades.

●Windscreen crack: the impact of a stone will

trigger a single wipe cycle with the rain sen-

sor on. Next the rain sensor detects the reduc-

tion in the sensitive surface area and adapts

accordingly. The behaviour of the sensor will

vary with the size of the damage caused by the

stone.

WARNING

The rain sensor may not detect enough rain

to switch on the wipers.

●If necessary, switch on the wipers manually

when water on the windscreen obstructs visi-

bility.

Note

●To remove wax and coatings, we recom-

mend a window cleaner containing alcohol.

●Do not put stickers on the windscreen in

front of the rain sensor. This may cause sen-

sor disruption or faults.

Mirrors

General safety instructions

The exterior and interior mirrors allow the

driver to observe vehicles driving behind and

adapt his or her driving behaviour accordingly.

For safe driving, it is important for the driver to

adjust the exterior mirrors and interior mirror

correctly before setting o.

When looking through the exterior mirrors and

the interior mirror, it is not possible to see the

entire area behind and to the sides of the vehi-

cle. These areas outside the eld of view are

known as the blind spot. Other road users and

objects may be in the blind spot.

WARNING

Adjusting the exterior mirrors and interior

mirror while driving can distract the driver.

This could cause accidents and lead to seri-

ous injuries

●Only adjust the exterior mirrors and inte-

rior mirror when the vehicle is stationary.

●When parking, changing lanes, overtaking

or turning, always keep a close eye on your

surroundings, as other road users or objects

may also be in the blind spot.

●Always make sure that the mirrors are ad-

justed correctly and that visibility to the rear

is not reduced by ice, snow, fogging or other

objects.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Ateca 2023 Seite 104

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Ateca 2023

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info