Bedienungsanleitung Cupra Ateca 2023 (Seite 305 von 355) (Englisch)

817294

305

Zoom out

Zoom in

Vorherige Seite

1/355

Nächste Seite

Wheels and tyres

305

Important information about wheels and tyres

●Avoid fast cornering and hard acceleration.

●Inspect the tyres for irregular wear from time

to time.

Tyre pressure

The values of the tyre pressure are shown on

the sticker label located on the read frame of

the front left door ›››Fig.203.

Insuicient or excessive pressure greatly re-

duces the useful life of the tyres and adversely

aects vehicle performance and ride. Correct

ination pressures are very important, espe-

cially at high speeds.

The tyre pressure must be adjusted according

to the load the vehicle is carrying. If the vehicle

is going to be fully loaded, increase the tyre

pressure to the maximum load value shown on

the sticker label ›››Fig.203.

Do not forget the spare wheel when checking

the tyre pressures: Keep this spare wheel ina-

ted to the highest pressure required for the

road wheels.

In the case of a minimised temporary spare

wheel (125/70 R16 or 125/70 R18) inate to a

pressure of 4.2 bar as indicated on the tyre

pressure label ›››Fig.203.

Depending on the vehicle, tyre pressure can

be adjusted to medium load to improve driv-

ing comfort (tyre pressure ›››Fig.203).

When driving with comfort tyre pressure fuel

consumption may increase slightly.

Driving style

Fast cornering, heavy acceleration and hard

braking (squealing tyres) all increase tyre wear.

Wheel balance

The wheels on new vehicles are balanced.

However, certain circumstances may lead to

imbalance (run-out), which is detected as vi-

brations in the steering wheel.

Unbalanced wheels should be rebalanced, as

they otherwise cause excessive wear on steer-

ing, suspension and tyres. A wheel must also

be rebalanced when a new tyre is tted or if a

tyre is repaired.

Incorrect wheel alignment

Incorrect running gear alignment causes ex-

cessive tyre wear, impairing the safety of the

vehicle. If you notice excessive tyre wear, you

should check wheel alignment at a specialised

CUPRA Service or SEAT Oicial Service.

WARNING

Unsuitable handling of the wheels and tyres

may lead to sudden tyre pressure losses, to

tread separation or even to a blow-out.

●The driver is responsible for ensuring that

all of the vehicle tyres are correctly ina-

ted to the right pressure. The recommen-

ded tyre pressure is indicated on the label

›››Fig.203.

●Check tyre pressures regularly and ensure

they are maintained at the pressures indica-

ted. Tyre pressure that is too low could cause

overheating, resulting in tread detachment

or even burst tyres.

●Tyre pressure should be that indicated on

the label when the tyres are cold at all times

›››Fig.203.

●Regularly check the cold ination pressure

of the tyres. If necessary, change the tyre

pressure of the vehicle tyres while they are

cold.

●Regularly check your tyres for damage and

wear.

●Never exceed the maximum permitted

speed or loads specied for the type of tyre

tted on your vehicle.

For the sake of the environment

Under-inated tyres will increase fuel con-

sumption.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Ateca 2023 Seite 305

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Ateca 2023

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info