Bedienungsanleitung Cupra Formentor - 2020 (Seite 296 von 352) (Englisch)

817289

296

Zoom out

Zoom in

Vorherige Seite

1/352

Nächste Seite

Practical tips

The position of the oil filler opening is shown

in the corresponding engine compartment

illustration

››› page 291 .

Engine oil specification

››› page 291 .

WARNING

Oil is highly inflammable! Ensure that no oil

comes into contact with hot engine com-

ponents when topping up.

CAUTION

If the oil level is above area

››› Fig. 186 A,

do not start the engine. This could result in

damage to the engine and catalytic con-

verter. Contact a specialised workshop.

For the sake of the environment

The oil level must never be above zone

››› Fig. 186 A. Otherwise oil can be drawn in

through the crankcase breather and leak

into the atmosphere via the exhaust sys-

tem.

Note

Before a long trip, we recommend finding

an engine oil that conforms to the corre-

sponding VW specifications and recom-

mend keeping it in the vehicle. This way,

the correct engine oil will always be availa-

ble for a top-up if needed.

Engine oil change

We recommend that you have the engine oil

changed by a Technical Service.

WARNING

Only change the engine oil yourself if you

have the specialist knowledge required!

●Before opening the bonnet, read and ob-

serve the warnings

››› page 289.

●Wait for the engine to cool down. Hot oil

may cause burn injuries.

●Wear eye protection to avoid injuries,

such as acid burns, caused by splashes of

oil.

●When removing the oil drain plug with

your fingers, keep your arm horizontal to

help prevent oil from running down your

arm.

●Wash your skin thoroughly if it comes into

contact with engine oil.

●Engine oil is poisonous! Used oil must be

stored in a safe place out of the reach of

children.

CAUTION

No additives should be used with engine oil.

This could result in engine damage. Any

damage caused by the use of such additives

would not be covered by the factory war-

ranty.

For the sake of the environment

●We recommend that you change the en-

gine oil and the filter at a technical service

centre.

●Never pour oil down drains or into the

ground.

●Use a suitable container when draining

the used oil. It must be large enough to

hold all the engine oil.

Cooling system

Coolant specifications

The engine cooling system is supplied from

the factory with a specially treated mixture of

water and at least 40 % of the additive

G12evo (TL-VW 774 J), purple. This mixture

gives the necessary frost protection down to

-25°C (-13°F) and protects the light alloy

parts of the engine cooling system against

corrosion. It also prevents scaling and con-

siderably raises the boiling point of the cool-

ant.

To protect the cooling system, the percent-

age of additive must always be at least 40 %,

even in warm climates where anti-freeze

protection is not required.

If for weather reasons further protection is

necessary, the proportion of additive may be

294

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Formentor - 2020 Seite 296

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Formentor - 2020

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info