Bedienungsanleitung Cupra Formentor - 2021 (Seite 48 von 391) (Englisch)

810365

Zoom out

Zoom in

Vorherige Seite

1/391

Nächste Seite

Emergencies

and request assistance from an authorised

technician.

●Disconnect the air compressor. Unscrew

the tyre inflator tube from the tyre valve.

●When the tyre pressure is between 2.5 and

2.0 bars, continue driving without exceeding

80 km/h (50 mph).

●Attach the sticker

››› Fig. 34 2 to the in-

strument cluster, within the driver's visual

field.

●Check the pressure again after 10 minutes

››› page 46.

WARNING

When inflating the wheel, the air compres-

sor and the inflator tube may become hot.

●Protect hands and skin from hot parts.

●Do not place the hot flexible inflator tube

or hot air compressor on flammable mate-

rial.

●Allow them to cool before storing the de-

vice.

●If it is not possible to inflate the tyre to at

least 2.0 bars (29 psi / 200 kPa), the tyre is

too badly damaged. The sealant is not in a

good condition to seal the tyre. Do not con-

tinue driving. Seek specialist assistance.

CAUTION

Switch off the air compressor after a maxi-

mum of 8 operational minutes to avoid

overheating! Before switching on the air

compressor again, let it cool for several mi-

nutes.

Check after 10 minutes of driving

Screw the inflator tube

››› Fig. 34 5 again

and check the pressure on the gauge 6.

1.3 bar (19 psi / 130 kPa) and lower:

●Stop the vehicle! The tyre cannot be

sealed sufficiently with the tyre mobility set.

●You should obtain professional assistance

››› .

1.4 bar (20 psi / 140 kPa) and higher:

●Set the tyre pressure to the correct value

again.

●Carefully resume your journey until you

reach the nearest specialised workshop

without exceeding 80 km/h (50 mph).

●Have the damaged tyre replaced.

WARNING

Driving with an unsealed tyre is dangerous

and can cause accidents and serious injury.

●Do not continue driving if the tyre pres-

sure is 1.3 bar (19 psi / 130 kPa) and lower.

●Seek specialist assistance.

Changing a wheel

What to do first

●Park the vehicle on a horizontal surface

and in a safe place as far away from traffic as

possible.

●Apply the electronic parking brake.

●Switch on the hazard warning lights.

●Manual transmission: engage 1st gear.

●Automatic transmission: switch on the

parking lock by pressing button P.

●If you are towing a trailer, unhitch it from

your vehicle.

●Make sure that the vehicle tool kit

››› page 43 and the spare wheel

››› page 347

are ready.

●Observe the applicable legislation for each

country (reflective vest, warning triangles,

etc.).

●All occupants should leave the vehicle and

wait in a safe place (for instance behind the

roadside crash barrier).

WARNING

●Always observe the above steps and pro-

tect yourself and other road users.

●If you change the wheel on a slope, block

the wheel on the opposite side of the car

with a stone or similar to prevent the vehi-

cle from moving.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Formentor - 2021 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Formentor - 2021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info