Bedienungsanleitung Cupra Formentor - 2021 (Seite 55 von 391) (Englisch)

810365

Zoom out

Zoom in

Vorherige Seite

1/391

Nächste Seite

Self-help

Removing the jump leads

Before you remove the jump leads,

switch off the dipped beam headlights if

they are switched on.

Turn on the heater blower and heated

rear window in the vehicle with the flat

battery. This helps minimise voltage

peaks which are generated when the

leads are disconnected.

When the engine is running, disconnect

the leads in reverse order to the details

given above.

Make sure the battery clamps have sufficient

metal-to-metal contact with the battery ter-

minals.

If the engine fails to start after about 10 sec-

onds, switch off the starter and try again af-

ter about 1 minute.

WARNING

●Please note the safety warnings referring

to working in the engine compartment

››› page 322.

●The battery providing assistance must

have the same voltage as the flat battery

(12V) and approximately the same capacity

(see imprint on battery). Failure to comply

could result in an explosion.

●Never use jump leads when one of the

batteries is frozen. Danger of explosion!

Even after the battery has thawed, battery

10.

11.

acid could leak and cause chemical burns.

If a battery freezes, it should be replaced.

●Keep sparks, flames and lighted ciga-

rettes away from batteries, danger of ex-

plosion. Failure to comply could result in an

explosion.

●Observe the instructions provided by the

manufacturer of the jump leads.

●Do not connect the negative cable from

the other vehicle directly to the negative

terminal of the flat battery. The gas emitted

from the battery could be ignited by sparks.

Danger of explosion.

●Never attach the negative cable to fuel

system components or the brake lines in

the other vehicle.

●The non-insulated parts of the battery

clamps must not be allowed to touch. The

jump lead attached to the positive battery

terminal must not touch metal parts of the

vehicle, this can cause a short circuit.

●Position the leads in such a way that they

cannot come into contact with any moving

parts in the engine compartment.

●Do not lean on the batteries. This could

result in chemical burns.

Note

The vehicles must not touch each other,

otherwise electricity could flow as soon as

the positive terminals are connected.

Tow start and towing

Introduction

Tow-starting means starting the engine of

the vehicle while another pulls it.

Towing means one vehicle pulling another

that is not roadworthy.

Always consider the legal provisions relating

to tow-starting and towing.

For technical reasons, towing a vehicle

with a discharged battery is not allowed.

The jump start should be used instead

››› page 52.

If the vehicle comes with the Keyless Access

system, towing is only allowed with the igni-

tion on!

The vehicle battery drains if the vehicle is

towed with the engine switched off and the

ignition connected. Depending on the bat-

tery charge status, the drop in voltage may

be so large, even after just a few minutes,

that no electrical device in the vehicle may

work e.g. the hazard warning lights. In vehi-

cles with the Keyless Access system, the

steering wheel could lock ››› .

WARNING

A vehicle with no power should never be

towed. »

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Formentor - 2021 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Formentor - 2021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info