Bedienungsanleitung Cupra Formentor - 2022 (Seite 352 von 396) (Englisch)

810366

352

Zoom out

Zoom in

Vorherige Seite

1/396

Nächste Seite

350

Wheels and tyres

●Place the spare wheel or temporary spare

wheel into position.

●Screw in the wheel bolts and tighten them a

little with the wheel wrench.

● Use the appropriate adapter to tighten the

anti-theft wheel bolts.

●Carefully lower the vehicle using the jack.

●Use the wheel spanner to tighten all of the

wheel nuts clockwise. Tighten the bolts in di-

agonal pairs (not in a circle).

● Put the caps, trim or full hubcap back on.

The wheel bolts should be clean and turn

easily. Before tting the spare wheel, inspect

the wheel condition and hub mounting surfa-

ces. These surfaces must be clean before t-

ting the wheel.

Tightening torque of the wheel nuts

The prescribed tightening torque for wheel

bolts for steel and alloy wheels is 140 Nm. After

changing a wheel, have the tightening torque

checked immediately with a torque wrench

that is working perfectly.

Before checking tightening torque, have any

rusty wheel bolts that are diicult to screw re-

placed and clean the wheel hub threads.

Never apply grease or oil to wheel bolts or to

the wheel hub threads. Even if the bolts have

been tightened to the prescribed torque, they

could come loose while driving.

Tyres with directional tread pattern

Tyres with directional tread pattern have been

designed to operate best when rotating in only

one direction. An arrow on the tyre sidewall

indicates the direction of rotation on tyres with

directional tread. Always observe the indicated

direction of rotation in order to guarantee op-

timum grip and help avoid aquaplaning, exces-

sive noise and wear.

If the tyre is mounted in the opposite direction

of rotation, drive with extreme caution, as the

tyre is no longer being used correctly. This is of

particular importance when the road surface is

wet. Change the tyre as soon as possible or re-

mount it with the correct direction of rotation.

Works after changing a wheel

●Replace the hub caps or wheel bolt caps (de-

pending on equipment).

●Return all tools to their proper storing loca-

tion.

●If the replaced wheel does not t in the spare

wheel housing, store it safely in the luggage

compartment ›››page281.

●Check the tyre pressure of the newly moun-

ted tyre as soon as possible.

●In vehicles tted with a tyre pressure indica-

tor, adjust the pressure and store it in memory

›››page350.

●Have the tightening torque of the wheel nuts

checked as soon as possible with a torque

wrench ›››page349. Meanwhile, drive care-

fully.

●Have the at tyre replaced as quickly as pos-

sible.

Tyre pressure monitor sys-

tem

Tyre pressure monitor indicator

Fig.229 Instrument panel: warning of loss

of tyre pressure.

The tyre pressure monitoring system compares

the individual speeds of each wheel and thus

the dynamic radius with the help of the ABS

sensors.

If the rolling circumference of one or more

wheels has changed, the tyre pressure moni-

toring indicator will indicate this on the instru-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Formentor - 2022 Seite 352

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Formentor - 2022

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info