Bedienungsanleitung Cupra Formentor e-HYBRID - 2023 (Seite 313 von 396) (Englisch)

810364

313

Zoom out

Zoom in

Vorherige Seite

1/396

Nächste Seite

Miscellaneous situations

311

Jump start

10.

11.

Connect one end of the red jump lead to

the positive + terminal of the vehicle with

the at battery A.

Connect the other end of the red jump

lead to the positive terminal + in the vehi-

cle providing assistance B.

Connect one end of the black jump lead

C to a suitable ground terminal, to a solid

piece of metal in the engine block, or to

the motor block itself.

Connect the other end of the black jump

lead D to a solid metal component bolted

to the engine block or to the engine block

itself of the vehicle with the at battery.

Do not connect it to a point near the bat-

tery.

Position the leads in such a way that they

cannot come into contact with any moving

parts in the engine compartment.

Starting

Start the engine of the vehicle with the

boosting battery and let it run at idling

speed.

Start the engine of the vehicle with the at

battery and wait for 2 or 3 minutes until the

engine is running.

Removing the jump leads

Before you remove the jump leads, switch

o the dipped beam headlights if they are

switched on.

Turn on the heater blower and heated rear

window in the vehicle with the at battery.

This helps minimise voltage peaks which

are generated when the leads are discon-

nected.

When the engine is running, disconnect

the leads in reverse order to the details

given above.

If the engine fails to start after about 10sec-

onds, switch o the starter and try again after

about 1 minute.

WARNING

●Please note the safety warnings referring

to working in the engine compartment

›››page320.

●The battery providing assistance must have

the same voltage as the at battery (12V)

and approximately the same capacity (see

imprint on battery). Failure to comply could

result in an explosion.

●Never use jump leads when one of the bat-

teries is frozen. Danger of explosion! Even

after the battery has thawed, battery acid

could leak and cause chemical burns. If a

battery freezes, it should be replaced.

●Keep sparks, ames and lighted cigarettes

away from batteries, danger of explosion.

Failure to comply could result in an explo-

sion.

●Observe the instructions provided by the

manufacturer of the jump leads.

●Do not connect the negative cable from

the other vehicle directly to the negative ter-

minal of the at battery. The gas emitted

from the battery could be ignited by sparks.

Danger of explosion.

●Never attach the negative cable to fuel sys-

tem components or the brake lines in the

other vehicle.

●The non-insulated parts of the battery

clamps must not be allowed to touch. The

jump lead attached to the positive battery

terminal must not touch metal parts of the

vehicle, this can cause a short circuit.

●Position the leads in such a way that they

cannot come into contact with any moving

parts in the engine compartment.

●Do not lean on the batteries. This could re-

sult in chemical burns.

●Take into account the instruction manual

of the jump lead manufacturer and the in-

struction manual of the other vehicle.

NOTICE

Immediately go to a specialist workshop and

have the 12volt battery checked.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Formentor e-HYBRID - 2023 Seite 313

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Formentor e-HYBRID - 2023

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info