Bedienungsanleitung Cupra Formentor e-HYBRID - 2023 (Seite 353 von 396) (Englisch)

810364

353

Zoom out

Zoom in

Vorherige Seite

1/396

Nächste Seite

Wheels and tyres

351

Tyre pressure monitor system

ment panel through a warning lamp and a

warning to the driver ›››Fig.229. When only

one specic tyre is aected, its position within

the vehicle will be indicated.

Loss of pressure: Check left tyre

pressure!

Wheel tread change

The wheel diameter changes when:

●Tyre pressure is changed manually.

●Tyre pressure is insuicient.

●The tyre structure is damaged.

●The vehicle is unbalanced because of a load.

● The wheels on an axle are subject to a heav-

ier load (e.g. with a heavy load).

●The vehicle is tted with snow chains.

●The temporary spare wheel is tted.

●The wheel on one axle is changed.

There may be a delay in the reaction of the tyre

pressure monitoring indicator or it may not

indicate anything under certain circumstances

(e.g. sporty driving, snow-covered or unpaved

roads, or when driving with snow chains).

Calibrate the tyre pressure monitoring indi-

cator

After changing the tyre pressure or replacing

one or more wheels, the tyre pressure moni-

toring indicator must be recalibrated. Do the

same, for example, when the front and rear

wheels are swapped.

It should be calibrated with the vehicle stop-

ped and its tyres cold. If calibrated while the

tyres are hot, the pressure check and calibra-

tion procedure should be repeated when cold

before the next trip.

●Switch the ignition on.

●Memorise the new ination pressure in the

Infotainment system: function button >

Vehicle info > Vehicle status ›››page34.

●OR: through the Service menu on the in-

strument cluster ›››page28.

The tyre pressure loss indicator uses the ABS

sensors to compare the turns of each wheel

and, therefore, their tread circumferences,

among other aspects. After a long journey with

varied speeds the programmed values are col-

lected and monitored.

With the wheels under very heavy loads, the

tyre pressure must be increased to the total

recommended tyre pressure before the cali-

bration ›››Fig.229.

WARNING

When the tyres are inated at dierent pres-

sures or at a pressure that is too low then a

tyre may be damaged resulting in a loss of

control of the vehicle and a serious or fatal

accident.

●If the lamp lights up, reduce speed im-

mediately and avoid any sudden turning or

braking manoeuvres. Stop when possible,

and check the tyre pressure and status.

●The tyre pressure loss indicator only works

correctly if all the tyres are at the correct

pressure when cold, and it is subsequently

calibrated according to the described proce-

dure.

●If a tyre has not been punctured and it does

not have to be changed immediately, drive to

the nearest specialised workshop at a mod-

erate speed and have the tyre checked and

inated to the correct pressure.

Note

●Driving for the rst time with new tyres at

a high speed can cause them to slightly ex-

pand, which could then produce an air pres-

sure warning.

●If excessively low tyre pressure is detected

with the ignition on, an audible warning will

sound. In the event that there is a fault in the

system, an audible warning will sound.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Formentor e-HYBRID - 2023 Seite 353

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Formentor e-HYBRID - 2023

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info