Bedienungsanleitung Cupra Leon 2018 (Seite 62 von 388) (Englisch)

817303

Zoom out

Zoom in

Vorherige Seite

1/388

Nächste Seite

The essentials

Connect the other end of the black jump

lead X to a solid metal component bol-

ted to the engine block or to the engine

block itself of the vehicle with the flat

battery. Do not connect it to a point near

the battery A.

Position the leads in such a way that

they cannot come into contact with any

moving parts in the engine compart-

ment.

Starting

Start the engine of the vehicle with the

boosting battery and let it run at idling

speed.

Start the engine of the vehicle with the

flat battery and wait for 2 or 3 minutes

until the engine is running.

Removing the jump leads

Before you remove the jump leads,

switch off the dipped beam headlights if

they are switched on.

Turn on the heater blower and heated

rear window in the vehicle with the flat

battery. This helps minimise voltage

peaks which are generated when the

leads are disconnected.

When the engine is running, disconnect

the leads in reverse order to the details

given above.

10.

11.

Make sure the battery clamps have sufficient

metal-to-metal contact with the battery ter-

minals.

If the engine fails to start after about 10 sec-

onds, switch off the starter and try again after

about 1 minute.

WARNING

●Please note the safety warnings referring

to working in the engine compartment

››› page 321.

●The battery providing assistance must

have the same voltage as the flat battery

(12V) and approximately the same capaci-

ty (see imprint on battery). Failure to com-

ply could result in an explosion.

●Never use jump leads when one of the

batteries is frozen. Danger of explosion!

Even after the battery has thawed, battery

acid could leak and cause chemical burns.

If a battery freezes, it should be replaced.

●Keep sparks, flames and lighted ciga-

rettes away from batteries, danger of ex-

plosion. Failure to comply could result in an

explosion.

●Observe the instructions provided by the

manufacturer of the jump leads.

●Do not connect the negative cable from

the other vehicle directly to the negative

terminal of the flat battery. The gas emit-

ted from the battery could be ignited by

sparks. Danger of explosion.

●Never attach the negative cable to fuel

system components or the brake lines in

the other vehicle.

●The non-insulated parts of the battery

clamps must not be allowed to touch. The

jump lead attached to the positive battery

terminal must not touch metal parts of the

vehicle, this can cause a short circuit.

●Position the leads in such a way that they

cannot come into contact with any moving

parts in the engine compartment.

●Do not lean on the batteries. This could

result in chemical burns.

Note

The vehicles must not touch each other,

otherwise electricity could flow as soon as

the positive terminals are connected.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Leon 2018 Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info