Bedienungsanleitung Cupra Leon e-HYBRID - 2022 (Seite 352 von 399) (Englisch)

810372

352

Zoom out

Zoom in

Vorherige Seite

1/399

Nächste Seite

350

Wheels and tyres

Fig.237 Crossbar: mounting the jack on

the vehicle.

●Rest the jack (vehicles tools) on rm ground.

If necessary use a large, strong board or similar

support. If the surface is slippery (for example

tiles) place the jack on a rubber mat or similar

to prevent it from slipping ››› .

●Look on the strut for the mark of the jack

support point (sunken area) closest to the

wheel to be changed ›››Fig.236.

●Turn the jack crank handle, located below

the strut support point, to raise it until the

tab 1 ›››Fig.237 is below the housing that

is provided.

● Align the jack so that the tab 1“grips”

onto the housing provided on the cross mem-

ber and the mobile base 2 is resting on the

ground. The base plate 2 should fall vertically

with respect to the support point 1 .

●Continue turning the jack until the wheel is

slightly lifted o the ground.

WARNING

The factory-supplied jack is only designed

for changing wheels on this model. On no

account attempt to use it for lifting heavier

vehicles or other loads. Risk of injury.

● Make sure the jack remains stable. If the

surface is slippery or soft, the jack could slip

or sink, respectively, with the consequent

risk of causing injuries.

● Lift the vehicle using only the jack supplied

from the factory. Other jacks, even those ap-

proved for other CUPRA models could slip,

with the consequent risk of injury.

●Place the jack only at the support points

provided on the strut and align it. Otherwise,

the jack could slip because it does not have

suicient grip on the vehicle: risk of injury!

●You should never place a body limb such as

an arm or leg under a raised vehicle that is

solely supported by the jack.

● If you have to work underneath the vehi-

cle, you must use suitable stands additionally

to support the vehicle, there is a risk of acci-

dent!.

●Never raise the vehicle if it is tilting to one

side or the engine is running.

●Never start the engine when the vehicle is

raised. The vehicle may come loose from the

jack due to the engine vibrations.

NOTICE

●The vehicle must not be raised on the

crossbar. Place the jack only at the support

points provided on the strut and align it. Oth-

erwise, the vehicle may be damaged.

●Any type of load or weight applied to the

external trim/door will (stepped on, tting

the jack, resting heavy objects, etc.) can

cause damage to it. CUPRA accepts no re-

sponsibility for any damages caused by im-

proper use of the external trim or body.

Removing and installing a wheel

Change the wheel after loosening the wheel

bolts and raising the vehicle with the jack.

When removing/tting the wheel, the rim may

hit and damage the brake disc. For this reason,

please take care and get a second person to

assist you.

Taking o the wheel

●Unscrew the bolts with the wheel wrench

and place them on a clean surface.

●Remove the wheel.

Putting on the spare wheel

Check the direction of rotation of the tyre

›››page351.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Leon e-HYBRID - 2022 Seite 352

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Leon e-HYBRID - 2022

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info