498382
16
Zoom out
Zoom in
Vorherige Seite
1/35
Nächste Seite
AUDIO / VIDEO CONNECTIONS
S-Video
Input Jack
S-Video
This is a higher quality connection than standard composite video. The S-Video connector is distinguishable by its 4 pins, as shown
below. If your TV has an S-Video input, it’s recommended that you use this type of connection for better picture quality.
Component Video / Progressive Scan
The highest quality video connection, Component Video requires the optional Component/P-SCAN Video Cable (not included),
with separate connectors for the Y, Pb/Cb, and Pr/Cr signals. This cable also supports the Progressive Scan mode when used with
high-end P-SCAN TVs. Using the component video output or P-SCAN mode requires these steps:
S-Video Cable
Connect the Composite / S-Video cable to the unit’s
Video Out and the black S-Video connector to the
corresponding input on your TV.
1
2
On your TV, select the S-Video input. This is normally
done by selecting “Video 2” or “AV2” with the TV’s
remote control. On some TVs, this is done by selecting a
particular channel.
3
Press the MONITOR key on the front panel of the DVD
player once to change the video output selection.
TV with
S-Video Input
S
VIDEO INPUT
16
4
You should now see the DVD players splash screen on
your TV.
2
Enter the Setup Menu (Page 30) by pressing SETUP on
the remote control or by using the FUNCTION key on the
player (Page 10). Change the VIDEO OUTPUT setting to
YCbCr and exit the SETUP MENU.
1
3
Press the MONITOR key to switch to External Video. You
should now see the player's Splash Screen on the TV.
Component Video
Input Jacks
Y Pb/Cb Pr/Cr
Component
Video Cable
(not included )
Connect the player to your TV using the Component
Video cable. Turn on the TV and select the appropriate
input for Component Video IN.
TV with
Component
Video Input
VIDEO INPUT
Y Pb Pr
TV OUTPUT
VIDEO OUTPUT
SCAN MODE
CONTRAST
SATURATION
NTSC
YCbCr
PROGRESSIVE
POWER
LCD
GOTO
PROGRAM
BOOKMARK
SUBTITLE
ANGLE
DISPLAY
MENU
TITLE
MONITOR
SETUP
PBC
TO SWITCH TO PROGRESSIVE SCAN MODE - Enter
SETUP again and change the SCAN MODE setting to
PROGRESSIVE. WARNING: Do not change this setting
unless you're sure your TV supports Progressive Scan.
4
To reset the MONITOR, power the
unit off and then back on.
The SCAN MODE can only be
changed to PROGRESSIVE after
the unit has been set to
EXTERNAL VIDEO OUTPUT mode.
!
!
Notes
Downloaded from www.Manualslib.com manuals search engine
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Cyberhome CH-LDV 700B wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info