Bedienungsanleitung Cyberhome CH-LDV712 (Seite 41 von 49) (Englisch)

498383

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

Video Setup Options

SYSTEM - NTSC / PAL

Your Player will work with TVs based on the NTSC and PAL

standards, as well as TVs, Monitors and Projectors supporting the

new Progressive Scan mode.

NTSC is the standard TV system used in the USA, Canada, Japan

and many other countries, supporting 480 Lines at 60Hz. The PAL TV

system is used in Europe, Africa and the Middle East, among others,

and supports 576 Lines at 50Hz.

ASPECT - 4:3 PS / 4:3 LB / 16:9 WS

You can setup your Player to work with normal and wide screen televisions. If you are using a wide screen TV, set

this option to 16:9 WS to match the aspect ratio of your TV. When used with a normal TV (4:3 aspect ratio), the 4:3

PS setting results in the typical “Pan & Scan” display, where a movie is clipped on the sides to fit on the TV screen.

The 4:3 LB setting will enable the “Letterbox” format, where the movie is presented in wide screen format with black

lines at the top and bottom of the screen.

OUTPUT - S-VIDEO / YCbCr / YPbPr

Change this setting to match the type of video input jack you are using on your TV. *If you are using a Progressive

Scan TV, you must change this setting FIRST, before the OUTPUT setting described above.

Composite Video is the most common video connection type and is supported on most TVs. If you connect

Composite Video to your TV, normally you don’t need to change OUTPUT settings, and your TV will get displayed. S-

Video is a higher quality video signal that is separated into brightness and color channels. YCbCr, or COMPONENT

video is used for TVs, Computer Monitors and Projectors that support three video inputs, one for a color channel

(Yellow, Blue, Red). YPbPr - P-SCAN, or Progressive Scan TVs are able to scan a complete video frame on each

pass, unlike normal “interlaced” TVs that require two passes to scan each frame.

Quick Tips

Resetting to the Player’s Default Video Settings

Make sure to use caution when changing the OUTPUT settings. If the value selected is not compatible with your

Television, you may no longer be able to see the screen. If this happens, follow the procedures below to reset

the player’s settings to default.



Turn the unit off unplugging the power cord or detaching the battery pack.



After a few seconds, power the unit on and LIFT THE DISC COVER.



Enter one of the following codes on the remote control depending on your TV type:

STOP - 2 - 0 - 0 - 2STOP - 2 - 0 - 0 - 3



The player is now reset to COMPOSITE Video Out and the TV SYSTEM you specified.

NTSC (USA): PAL (Europe):

*If you are not sure that you are using a P-Scan TV, don’t change this setting until AFTER changing the OUTPUT

setting discussed below. If this happens, however, you’ll need to reset the player as outlined below. For details on

setting up the player with a Progress Scan TV, see pg 18.

LANG.

VIDEO

AUDIO

CHILD

OTHERS

EXIT

SYSTEM

ASPECT

OUTPUT

ENTER

RETURN SETUP

NTSC

16:9 WS

YPbPr

For Help on Using the Setup Menu, see pg 38.

Downloaded from www.Manualslib.com manuals search engine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cyberhome CH-LDV712 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info